Понадобилось пару месяцев назад восстановить прошивку на бюджетном NAS-хранилище Iomega IX2-ng (оно же IX2-dl). Все найденные руководства относились к предыдущей модели IX2-200 и были неактуальны.
Ситуация незатейлива, поупалось хранилище с двумя дисками по 1Тб, а хотелось установить 2x3Tb. Владелец, не зная особенностей устройства, просто вытащил оба диска и сразу их отформатировал, потом вставил новые и получил мигающий "кирпич". Как позже оказалось, прошивка хранилсь на самих же дисках и подобных историй в Интернете масса. Менять же диски нужно по одному: один заменил, сразу синхронизировал, потом второй - синхронизировал. После этого можно расширить том на появившееся свободное пространство. Ну, в общем, было поздно.
После некоторых мытарств, удалось "родить" инструкцию:- Скачиваем образ прошивки с офф. сайта. Или с обменника. Объём 198 мб. Ссылку удалось выбить у тех. поддержки. На официальном сайте можно скачать только зашифрованную прошивку. Её, в принципе, можно расшифровать, но если есть готовое, то почему бы не воспользоваться.
- Распаковываем архив, вставляем флешку, объёмом свыше 1 Гб. И запускаем ix2-ng-3.3.2.29823.exe. Утилита запишет прошивку на флешку (\emctools\ix2-dl_images\ix2-ng-3.3.2.29823_imager.tgz).
- Далее, извлекаем два файла zImage и initrd из архива ix2-ng-3.3.2.29823_imager.tgz на комп с Linux (я использовал VirtualBox-машину с Ubuntu). Нам нужна утилита dd (возможно подойдёт и Windows-порт dd).
- Безопасно извлекаем флешку с прошивкой.
- С нового жёсткого диска удаляем все разделы. Я использовал Hitachi 3Tb. Инициализируем его, записываем таблицу разделов MBR или GPT (для дисков свыше 2Тб).
- После этого нужно записать файлы загрузчика на этот винт (я подключал винт через кабель USB->SATA и пробрасывал в виртуальную машину).
dd if=zImage of=/dev/sdX bs=512 seek=20485477+1 records in
5477+1 records out
2804492 bytes (2.8 MB) copied, 1.4704 s, 1.9 MB/sdd if=initrd of=/dev/sdX bs=512 seek=81925673+1 records in
5673+1 records out
2905045 bytes (2.9 MB) copied, 0.370494 s, 7.8 MB/s - Вставляем жёсткий диск и флешку в пациента, зажимаем кнопку RESET и вставляем кабель питания.
- IX2 включится и начнёт загрузку с HDD. Загрузится ядро, инициализация шины USB, определит, что винт не содержит прошивку и попытается её восстановить с флешки. Когда загорятся две красных светодиода, можно отпустить кнопку RESET. Всё это занимает примерно 30 секунд.
- Когда прошивка успешно завершится, устройство должно выключиться САМОСТОЯТЕЛЬНО. Минут 10-15. Уже точно не помню. Если устройство не выключается, значит что-то пошло не так и для диагностики нужно подключаться к консоли. Об этом ниже.
- После включения и загрузки, можно зайти в веб-интерфейс. Пароль по умолчанию admin/(пусто). Пароль по умолчанию для ssh (root/soho)
Если восстановить "вслепую" не получается, то необходимо подключаться к последовательной консоли устройства. Для это на плате есть 4ёхпиновый разьём, к которому можно подключиться при помощи преобразователя USB-TO-TTL. Я заказывал из Китая, цены смешные. Порядка 30 рублей за штуку.
Распиновка следующая:
| Pin 1 | VCC (3.3V) |
| Pin 2 | TxD |
| Pin 3 | GND |
| Pin 4 | RxD |
Ну или "вживую" выглядит это так:
Ниже можно посмотреть подробные логи PuTTY с консоли устройства в процессе восстановления.
Ну и далее, при помощи любой программы эмулятора терминала подключаемся к консоли (я использовал PuTTY).
Настройки порта: 115200, parity none, flow control xon/xoff, 8 data bits, 1 stop bit.
Ниже приведен полные логи восстановления и первой загрузки.
Лог первой загрузки:
Тема на forum.nas-central.org.
Ну и далее, при помощи любой программы эмулятора терминала подключаемся к консоли (я использовал PuTTY).
Настройки порта: 115200, parity none, flow control xon/xoff, 8 data bits, 1 stop bit.
Ниже приведен полные логи восстановления и первой загрузки.
Лог восстановления:
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__| ** ix2-spi ** ** uboot_ver:0.0.8 **
** MARVELL BOARD: DB-88F6282A-BP LE
U-Boot 1.1.4 (Oct 28 2011 - 15:18:22) Marvell version: 3.6.1 - EMC
U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CD5A0
Soc: 88F6282 A1 CPU running @ 1600Mhz L2 running @ 800Mhz
SysClock = 533Mhz , TClock = 200Mhz
DRAM (DDR3) CAS Latency = 7 tRP = 7 tRAS = 20 tRCD=7
DRAM CS[0] base 0x00000000 size 256MB
DRAM Total size 256MB 16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
Found ADT7473, program PWM1 ... OK
[1024kB@f8000000] Flash: 1 MB
Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (6)
Device 0 @ 0 0:
Model: ST250DM000-1BD141 Firm: KC45 Ser#: 9VYHEAE0
Type: Hard Disk
Supports 48-bit addressing
Capacity: 238475.1 MB = 232.8 GB (488397168 x 512)
CPU : Marvell Feroceon (Rev 1)
Streaming disabled
Write allocate disabled
USB 0: host mode
PEX 0: interface detected no Link.
PEX 1: interface detected no Link.
Net: egiga0 [PRIME]
Hit any key to stop autoboot: 3 2 1 0
Reset IDE:
Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (6)
Device 0 @ 0 0:
Model: ST250DM000-1BD141 Firm: KC45 Ser#: 9VYHEAE0
Type: Hard Disk
Supports 48-bit addressing
Capacity: 238475.1 MB = 232.8 GB (488397168 x 512)
IDE read: device 0 block # 2048, count 6144 ... 6144 blocks read: OK
IDE read: device 0 block # 8192, count 6144 ... 6144 blocks read: OK
## Booting image at 00040000 ...
Image Name: Linux-2.6.31.8
Created: 2012-10-04 20:59:31 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2804428 Bytes = 2.7 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
## Loading Ramdisk Image at 00900000 ...
Image Name:
Created: 2012-11-09 21:52:49 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 2904981 Bytes = 2.8 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Starting kernel ...
Linux version 2.6.31.8 (soho@bsoho080.lss.emc.com) (gcc version 4.3.2 (Sourcery G++ Lite 2008q3-72) ) Thu Oct 4 16:59:24 EDT 2012 v0.0.9 Thu Oct 4 16:59:24 EDT 2012
CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977
CPU: VIVT data cache, VIVT instruction cache
Machine: Feroceon-KW
Using UBoot passing parameters structure
Memory policy: ECC disabled, Data cache writeback
Built 1 zonelists in Zone order, mobility grouping off. Total pages: 64960
Kernel command line: console=ttyS0,115200 root=/dev/ram0 mtdparts=spi_flash:0x7e000@0(u-boot),0x1000@0x7f000(env),0x1000@0x7e000(env2) :::DB88FXX81:eth0:none
PID hash table entries: 1024 (order: 10, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 256MB = 256MB total
Memory: 243968KB available (5196K code, 325K data, 140K init, 0K highmem)
Hierarchical RCU implementation.
NR_IRQS:128
Console: colour dummy device 80x30
Calibrating delay loop... 1589.24 BogoMIPS (lpj=7946240)
Security Framework initialized
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
xor: measuring software checksum speed
arm4regs : 1446.000 MB/sec
8regs : 1096.000 MB/sec
32regs : 1070.800 MB/sec
xor: using function: arm4regs (1446.000 MB/sec)
NET: Registered protocol family 16
Feroceon L2: Enabling L2
Feroceon L2: Cache support initialised.
CPU Interface
-------------
SDRAM_CS0 ....base 00000000, size 256MB
SDRAM_CS1 ....disable
SDRAM_CS2 ....disable
SDRAM_CS3 ....disable
PEX0_MEM ....base e0000000, size 128MB
PEX0_IO ....base f2000000, size 1MB
PEX1_MEM ....base e8000000, size 128MB
PEX1_IO ....base f2100000, size 1MB
INTER_REGS ....base f1000000, size 1MB
NFLASH_CS ....base fa000000, size 2MB
SPI_CS ....base f4000000, size 16MB
BOOT_ROM_CS ....no such
DEV_BOOTCS ....no such
CRYPT_ENG ....base f0000000, size 2MB
Marvell Development Board (LSP Version KW_LSP_5.1.3_patch25)-- DB-88F6282A-BP Soc: 88F6282 A1 LE
Detected Tclk 200000000 and SysClk 533333333
MV Buttons Device Load
Marvell USB EHCI Host controller #0: c8040740
PEX0 interface detected no Link.
PEX1 interface detected no Link.
PCI: bus0: Fast back to back transfers enabled
PCI: bus1: Fast back to back transfers enabled
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
raid6: int32x1 133 MB/s
raid6: int32x2 156 MB/s
raid6: int32x4 164 MB/s
raid6: int32x8 126 MB/s
raid6: using algorithm int32x4 (164 MB/s)
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
NET: Registered protocol family 1
Trying to unpack rootfs image as initramfs...
rootfs image is not initramfs (no cpio magic); looks like an initrd
Freeing initrd memory: 2836K
rtc mv_rtc: rtc core: registered kw-rtc as rtc0
RTC registered
XOR registered 4 channels
XOR 2nd invalidate WA enabled
cesadev_init(c000edd4)
mvCesaInit: sessions=640, queue=64, pSram=f0000000
MV Buttons Driver Load
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
squashfs: version 4.0 (2009/01/31) Phillip Lougher
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
SGI XFS with ACLs, security attributes, large block/inode numbers, no debug enabled
SGI XFS Quota Management subsystem
msgmni has been set to 482
alg: No test for cipher_null (cipher_null-generic)
alg: No test for ecb(cipher_null) (ecb-cipher_null)
alg: No test for digest_null (digest_null-generic)
alg: No test for compress_null (compress_null-generic)
alg: No test for stdrng (krng)
alg: No test for hmac(digest_null) (hmac(digest_null-generic))
async_tx: api initialized (sync-only)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
io scheduler noop registered
io scheduler anticipatory registered (default)
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xf1012100 (irq = 34) is a 16550A
console [ttyS0] enabled
brd: module loaded
loop: module loaded
Integrated Sata device found
IRQ 21/mvSata: IRQF_DISABLED is not guaranteed on shared IRQs
scsi0 : Marvell SCSI to SATA adapter
scsi1 : Marvell SCSI to SATA adapter
scsi 0:0:0:0: Direct-Access Seagate ST250DM000-1BD14 KC45 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] Sector size 0 reported, assuming 512.
sd 0:0:0:0: [sda] 488397168 512-byte logical blocks: (250 GB/232 GiB)
sd 0:0:0:0: [sda] 0-byte physical blocks
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 0:0:0:0: [sda] Write Protect is off
Loading Marvell Ethernet Driver:
o Cached descriptors in DRAM
o DRAM SW cache-coherency
o 2 Giga ports supported
o Single RX Queue support - ETH_DEF_RXQ=0
o Single TX Queue support - ETH_DEF_TXQ=0
o TCP segmentation offload (TSO) supported
o Large Receive offload (LRO) supported
o Receive checksum offload supported
o Transmit checksum offload supported
o Network Fast Processing (Routing) supported - (Disabled)
o Proc tool API enabled
o SKB Reuse supported - (Disabled)
o SKB Recycle supported - (Disabled)
o Rx descripors: q0=256
o Tx descripors: q0=532
o Loading network interface(s):
o register under mv88fx_eth platform
o eth0, ifindex = 2, GbE port = 0
Warning: Giga 1 is Powered Off
mvFpRuleDb (c0928000): 2048 entries, 8192 bytes
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA
sd 0:0:0:0: [sda] Sector size 0 reported, assuming 512.
SPI Serial flash detected @ 0xf4000000, 1024KB (256sec x 4KB)
3 cmdlinepart partitions found on MTD device spi_flash
Creating 3 MTD partitions on "spi_flash":
0x000000000000-0x00000007e000 : "u-boot"
0x00000007f000-0x000000080000 : "env"
0x00000007e000-0x00000007f000 : "env2"
sda:Using Hamming 1-bit ECC for NAND device
No NAND device found!!!
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci_marvell ehci_marvell.70059: Marvell Orion EHCI
ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus number 1
sd 0:0:0:0: [sda] Sector size 0 reported, assuming 512.
sd 0:0:0:0: [sda] Attached SCSI disk
ehci_marvell ehci_marvell.70059: irq 19, io base 0xf1050100
ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
uhci_hcd: USB Universal Host Controller Interface driver
usbcore: registered new interface driver usblp
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver ums-datafab
usbcore: registered new interface driver ums-freecom
usbcore: registered new interface driver ums-jumpshot
usbcore: registered new interface driver ums-sddr09
usbcore: registered new interface driver ums-sddr55
usbcore: registered new interface driver ums-usbat
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
adt7473 0-002e: adt7473 chip found
iBoard_model 2
md: linear personality registered for level -1
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
md: raid10 personality registered for level 10
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
dm_crypt using the OCF package.
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
TCP cubic registered
NET: Registered protocol family 17
NET: Registered protocol family 5
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
rtc mv_rtc: setting system clock to 2013-03-06 02:56:53 UTC (1362538613)
md: Waiting for all devices to be available before autodetect
md: If you don't use raid, use raid=noautodetect
md: Autodetecting RAID arrays.
md: Scanned 0 and added 0 devices.
md: autorun ...
md: ... autorun DONE.
RAMDISK: gzip image found at block 0
usb 1-1: new high speed USB device using ehci_marvell and address 2
VFS: Mounted root (ext2 filesystem) on device 1:0.
Looking for shell in cmdline: console=ttyS0,115200 root=/dev/ram0 mtdparts=spi_flash:0x7e000@0(u-boot),0x1000@0x7f000(env),0x1000@0x7e000(env2) :::DB88FXX81:eth0:none
Make node for mtd devices
HDD /dev/sda detected
cat: can't open '/sys/block/sdb/removable': No such file or directory
sh: mtd5: unknown operand
Create fw_env.config in /etc
Model name is ix2-ng
mdadm: cannot open /dev/sda1: No such device or address
cat: can't open '/sys/block/sda/sda1/size': No such file or directory
mdadm: No devices to examine
cat: can't open '/sys/block///size': No such file or directory
Valid Disk 1 in md0:
Valid Disk 2 in md0:
USB Device node is /dev/sdb1
Checking to see the if the reset button is presusb 1-1: configuration #1 chosen from 1 choice
sed or not
Starscsi2 : SCSI emulation for USB Mass Storage devices
ted
/dev/btns file does not exist creating it
Opened /dev/btns with fd 3
Checking status of reset button
Button Check 1:
The Button ID from drive is 2 push_cntr is 1 release_cntr is 0
Reset Button is pressed
Checking if there is an attached EMC Imager
scsi 2:0:0:0: Direct-Access JetFlash Transcend 2GB 8.07 PQ: 0 ANSI: 2
sd 2:0:0:0: Attached scsi generic sg1 type 0
sd 2:0:0:0: [sdb] 4100096 512-byte logical blocks: (2.09 GB/1.95 GiB)
sd 2:0:0:0: [sdb] Write Protect is off
sd 2:0:0:0: [sdb] Assuming drive cache: write through
sd 2:0:0:0: [sdb] Assuming drive cache: write through
sdb: sdb1
sd 2:0:0:0: [sdb] Assuming drive cache: write through
sd 2:0:0:0: [sdb] Attached SCSI removable disk
FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
Checking for pre-image script... none.
Image tar file found: /usb_drive/emctools/ix2-ng_images/*.tgz
Extract Image tar file.
upgrade.xml
zImage
zImage.md5
initrd
initrd.md5
config
config.md5
apps
apps.md5
oem
oem.md5
lvmsetarchive
sshdupd.py
sslcertupd.py
menu.lst
inittab
logrotate.conf
ix2-ng_SPI_copy_kernel_initrd
sslupd.py
enableatmosupgrade.py
Upgrade_USBShares.py
updateacl
zeroconf
apps is valid
config is valid
initrd is valid
zImage is valid
Found EMC Imager with apps and config image...
Started USB Imaging...
md: md0 stopped.
mdadm: stopped /dev/md0
mdadm: /dev/md0 not identified in config file.
---Mounting volume
mount: mounting /dev/md0_vg/BFDlv on sysroot/boot failed: No such file or directory
Going to do a full install
umount: cannot umount /sysroot/boot: Invalid argument
---Stop volumes
Volume group "md0_vg" not found
---Stop raid
md: md0 stopped.
mdadm: stopped /dev/md0
---destroy raid
mdadm: Couldn't open /dev/sda1 for write - not zeroing
---Prepping drive: sda
Error: Partition doesn't exist.
Error: Partition doesn't exist.
10000+0 records in
10000+0 records out
---Creating partition on /dev/sda
Information: You may need to update /etc/fstab.
Information: You may need to update /etc/fstab.
Information: You may need to update /etc/fstab.
---Starting raid
md: bind<sda1>
raid1: raid set md0 active with 1 out of 2 mirrors
md0: detected capacity change from 0 to 21474770944
mdadm: array /dev/md0 started.
---Creating volumes
md0: unknown partition table
Physical volume "/dev/md0" successfully created
Volume group "md0_vg" successfully created
Logical volume "BFDlv" created
---Formatting partitions
mke2fs 1.41.3 (12-Oct-2008)
ext2fs_check_if_mount: No such file or directory while determining whether /dev/md0_vg/BFDlv is mounted.
Filesystem label=
OS type: Linux
Block size=4096 (log=2)
Fragment size=4096 (log=2)
262144 inodes, 1048576 blocks
52428 blocks (5.00%) reserved for the super user
First data block=0
Maximum filesystem blocks=1073741824
32 block groups
32768 blocks per group, 32768 fragments per group
8192 inodes per group
Superblock backups stored on blocks:
32768, 98304, 163840, 229376, 294912, 819200, 884736
Writing inode tables: 0/32 1/32 2/32 3/32 4/32 5/32 6/32 7/32 8/32 9/32 10/32 11/32 12/32 13/32 14/32 15/32 16/32 17/32 18/32 19/32 20/32 21/32 22/32 23/32 24/32 25/32 26/32 27/32 28/32 29/32 30/32 31/32 done
Writing superblocks and filesystem accounting information: done
This filesystem will be automatically checked every 29 mounts or
180 days, whichever comes first. Use tune2fs -c or -i to override.
---Mounting volume
1 logical volume(s) in volume group "md0_vg" now active
---Copying system image files
Copied apps config and oem image
BusyBox v1.9.2 (2012-11-09 16:52:11 EST) multi-call binary
Usage: cp [OPTION]... SOURCE DEST
Copy SOURCE to DEST, or multiple SOURCE(s) to DIRECTORY
Options:
-a Same as -dpR
-d,-P Preserve links
-H,-L Dereference all symlinks (default)
-p Preserve file attributes if possible
-f Force overwrite
-i Prompt before overwrite
-R,-r Recurse directories
-l,-s Create (sym)links
BusyBox v1.9.2 (2012-11-09 16:52:11 EST) multi-call binary
Usage: cp [OPTION]... SOURCE DEST
Copy SOURCE to DEST, or multiple SOURCE(s) to DIRECTORY
Options:
-a Same as -dpR
-d,-P Preserve links
-H,-L Dereference all symlinks (default)
-p Preserve file attributes if possible
-f Force overwrite
-i Prompt before overwrite
-R,-r Recurse directories
-l,-s Create (sym)links
---Stop volumes
---Stop raid
md: md0 stopped.
md: unbind<sda1>
md: export_rdev(sda1)
mdadm: stopped /dev/md0
---Writing hidden sectors
5477+1 records in
5477+1 records out
5673+1 records in
5673+1 records out
Remove the temp folder.
DONE copying images
Imaging Successful. Please remove the USB drive before the next power on
USB/DOM device is sdb
cat: can't open '/sys/block/sdc/removable': No such file or directory
Drives are sd[a]
/dev/sda:
/dev/sda:
setting drive write-caching to 0 (off)
write-caching = 0 (off)
/dev/sda:
issuing standby command
Constructing root filesystem...
Bootstrapping ...
tmpfs: No value for mount option 'relatime'
mount: mounting none on / failed: Invalid argument
Initialization complete.
Freeing init memory: 140K
init started: BusyBox v1.9.2 (2012-11-09 16:52:11 EST)
starting pid 807, tty '': '/etc/init.d/rcS'
starting pid 810, tty '': 'umount'
BusyBox v1.9.2 (2012-11-09 16:52:11 EST) multi-call binary
Usage: umount [flags] FILESYSTEM|DIRECTORY
Unmount file systems
Options:
-r Try to remount devices as read-only if mount is busy
-l Lazy umount (detach filesystem)
-f Force umount (i.e., unreachable NFS server)
-D Do not free loop device (if a loop device has been used)
The system is going down NOW!
Sending SIGTERM to all processes
Sending SIGKILL to all processes
Requesting system poweroff
md: stopping all md devices.
sd 0:0:0:0: [sda] Synchronizing SCSI cache
Power down.
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__| ** ix2-spi ** ** uboot_ver:0.0.8 **
** MARVELL BOARD: DB-88F6282A-BP LE
U-Boot 1.1.4 (Oct 28 2011 - 15:18:22) Marvell version: 3.6.1 - EMC
U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CD5A0
Soc: 88F6282 A1 CPU running @ 1600Mhz L2 running @ 800Mhz
SysClock = 533Mhz , TClock = 200Mhz
DRAM (DDR3) CAS Latency = 7 tRP = 7 tRAS = 20 tRCD=7
DRAM CS[0] base 0x00000000 size 256MB
DRAM Total size 256MB 16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
Found ADT7473, program PWM1 ... OK
[1024kB@f8000000] Flash: 1 MB
Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (6)
Device 0 @ 0 0:
Model: ST250DM000-1BD141 Firm: KC45 Ser#: 9VYHEAE0
Type: Hard Disk
Supports 48-bit addressing
Capacity: 238475.1 MB = 232.8 GB (488397168 x 512)
CPU : Marvell Feroceon (Rev 1)
Streaming disabled
Write allocate disabled
USB 0: host mode
PEX 0: interface detected no Link.
PEX 1: interface detected no Link.
Net: egiga0 [PRIME]
Hit any key to stop autoboot: 3 2 1 0
Reset IDE:
Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (6)
Device 0 @ 0 0:
Model: ST250DM000-1BD141 Firm: KC45 Ser#: 9VYHEAE0
Type: Hard Disk
Supports 48-bit addressing
Capacity: 238475.1 MB = 232.8 GB (488397168 x 512)
IDE read: device 0 block # 2048, count 6144 ... 6144 blocks read: OK
IDE read: device 0 block # 8192, count 6144 ... 6144 blocks read: OK
## Booting image at 00040000 ...
Image Name: Linux-2.6.31.8
Created: 2012-10-04 20:59:31 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2804428 Bytes = 2.7 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
## Loading Ramdisk Image at 00900000 ...
Image Name:
Created: 2012-11-09 21:52:49 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 2904981 Bytes = 2.8 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Starting kernel ...
Linux version 2.6.31.8 (soho@bsoho080.lss.emc.com) (gcc version 4.3.2 (Sourcery G++ Lite 2008q3-72) ) Thu Oct 4 16:59:24 EDT 2012 v0.0.9 Thu Oct 4 16:59:24 EDT 2012
CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977
CPU: VIVT data cache, VIVT instruction cache
Machine: Feroceon-KW
Using UBoot passing parameters structure
Memory policy: ECC disabled, Data cache writeback
Built 1 zonelists in Zone order, mobility grouping off. Total pages: 64960
Kernel command line: console=ttyS0,115200 root=/dev/ram0 mtdparts=spi_flash:0x7e000@0(u-boot),0x1000@0x7f000(env),0x1000@0x7e000(env2) :::DB88FXX81:eth0:none
PID hash table entries: 1024 (order: 10, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 256MB = 256MB total
Memory: 243968KB available (5196K code, 325K data, 140K init, 0K highmem)
Hierarchical RCU implementation.
NR_IRQS:128
Console: colour dummy device 80x30
Calibrating delay loop... 1589.24 BogoMIPS (lpj=7946240)
Security Framework initialized
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
xor: measuring software checksum speed
arm4regs : 1446.000 MB/sec
8regs : 1096.000 MB/sec
32regs : 1070.800 MB/sec
xor: using function: arm4regs (1446.000 MB/sec)
NET: Registered protocol family 16
Feroceon L2: Enabling L2
Feroceon L2: Cache support initialised.
CPU Interface
-------------
SDRAM_CS0 ....base 00000000, size 256MB
SDRAM_CS1 ....disable
SDRAM_CS2 ....disable
SDRAM_CS3 ....disable
PEX0_MEM ....base e0000000, size 128MB
PEX0_IO ....base f2000000, size 1MB
PEX1_MEM ....base e8000000, size 128MB
PEX1_IO ....base f2100000, size 1MB
INTER_REGS ....base f1000000, size 1MB
NFLASH_CS ....base fa000000, size 2MB
SPI_CS ....base f4000000, size 16MB
BOOT_ROM_CS ....no such
DEV_BOOTCS ....no such
CRYPT_ENG ....base f0000000, size 2MB
Marvell Development Board (LSP Version KW_LSP_5.1.3_patch25)-- DB-88F6282A-BP Soc: 88F6282 A1 LE
Detected Tclk 200000000 and SysClk 533333333
MV Buttons Device Load
Marvell USB EHCI Host controller #0: c8040740
PEX0 interface detected no Link.
PEX1 interface detected no Link.
PCI: bus0: Fast back to back transfers enabled
PCI: bus1: Fast back to back transfers enabled
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
raid6: int32x1 133 MB/s
raid6: int32x2 156 MB/s
raid6: int32x4 164 MB/s
raid6: int32x8 126 MB/s
raid6: using algorithm int32x4 (164 MB/s)
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
NET: Registered protocol family 1
Trying to unpack rootfs image as initramfs...
rootfs image is not initramfs (no cpio magic); looks like an initrd
Freeing initrd memory: 2836K
rtc mv_rtc: rtc core: registered kw-rtc as rtc0
RTC registered
XOR registered 4 channels
XOR 2nd invalidate WA enabled
cesadev_init(c000edd4)
mvCesaInit: sessions=640, queue=64, pSram=f0000000
MV Buttons Driver Load
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
squashfs: version 4.0 (2009/01/31) Phillip Lougher
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
SGI XFS with ACLs, security attributes, large block/inode numbers, no debug enabled
SGI XFS Quota Management subsystem
msgmni has been set to 482
alg: No test for cipher_null (cipher_null-generic)
alg: No test for ecb(cipher_null) (ecb-cipher_null)
alg: No test for digest_null (digest_null-generic)
alg: No test for compress_null (compress_null-generic)
alg: No test for stdrng (krng)
alg: No test for hmac(digest_null) (hmac(digest_null-generic))
async_tx: api initialized (sync-only)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
io scheduler noop registered
io scheduler anticipatory registered (default)
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xf1012100 (irq = 34) is a 16550A
console [ttyS0] enabled
brd: module loaded
loop: module loaded
Integrated Sata device found
IRQ 21/mvSata: IRQF_DISABLED is not guaranteed on shared IRQs
scsi0 : Marvell SCSI to SATA adapter
scsi1 : Marvell SCSI to SATA adapter
scsi 0:0:0:0: Direct-Access Seagate ST250DM000-1BD14 KC45 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] Sector size 0 reported, assuming 512.
sd 0:0:0:0: [sda] 488397168 512-byte logical blocks: (250 GB/232 GiB)
sd 0:0:0:0: [sda] 0-byte physical blocks
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 0:0:0:0: [sda] Write Protect is off
Loading Marvell Ethernet Driver:
o Cached descriptors in DRAM
o DRAM SW cache-coherency
o 2 Giga ports supported
o Single RX Queue support - ETH_DEF_RXQ=0
o Single TX Queue support - ETH_DEF_TXQ=0
o TCP segmentation offload (TSO) supported
o Large Receive offload (LRO) supported
o Receive checksum offload supported
o Transmit checksum offload supported
o Network Fast Processing (Routing) supported - (Disabled)
o Proc tool API enabled
o SKB Reuse supported - (Disabled)
o SKB Recycle supported - (Disabled)
o Rx descripors: q0=256
o Tx descripors: q0=532
o Loading network interface(s):
o register under mv88fx_eth platform
o eth0, ifindex = 2, GbE port = 0
Warning: Giga 1 is Powered Off
mvFpRuleDb (c0928000): 2048 entries, 8192 bytes
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA
sd 0:0:0:0: [sda] Sector size 0 reported, assuming 512.
SPI Serial flash detected @ 0xf4000000, 1024KB (256sec x 4KB)
3 cmdlinepart partitions found on MTD device spi_flash
Creating 3 MTD partitions on "spi_flash":
0x000000000000-0x00000007e000 : "u-boot"
0x00000007f000-0x000000080000 : "env"
0x00000007e000-0x00000007f000 : "env2"
sda:Using Hamming 1-bit ECC for NAND device
No NAND device found!!!
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci_marvell ehci_marvell.70059: Marvell Orion EHCI
ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus number 1
sd 0:0:0:0: [sda] Sector size 0 reported, assuming 512.
sd 0:0:0:0: [sda] Attached SCSI disk
ehci_marvell ehci_marvell.70059: irq 19, io base 0xf1050100
ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
uhci_hcd: USB Universal Host Controller Interface driver
usbcore: registered new interface driver usblp
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver ums-datafab
usbcore: registered new interface driver ums-freecom
usbcore: registered new interface driver ums-jumpshot
usbcore: registered new interface driver ums-sddr09
usbcore: registered new interface driver ums-sddr55
usbcore: registered new interface driver ums-usbat
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
adt7473 0-002e: adt7473 chip found
iBoard_model 2
md: linear personality registered for level -1
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
md: raid10 personality registered for level 10
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
dm_crypt using the OCF package.
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
TCP cubic registered
NET: Registered protocol family 17
NET: Registered protocol family 5
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
rtc mv_rtc: setting system clock to 2013-03-06 02:56:53 UTC (1362538613)
md: Waiting for all devices to be available before autodetect
md: If you don't use raid, use raid=noautodetect
md: Autodetecting RAID arrays.
md: Scanned 0 and added 0 devices.
md: autorun ...
md: ... autorun DONE.
RAMDISK: gzip image found at block 0
usb 1-1: new high speed USB device using ehci_marvell and address 2
VFS: Mounted root (ext2 filesystem) on device 1:0.
Looking for shell in cmdline: console=ttyS0,115200 root=/dev/ram0 mtdparts=spi_flash:0x7e000@0(u-boot),0x1000@0x7f000(env),0x1000@0x7e000(env2) :::DB88FXX81:eth0:none
Make node for mtd devices
HDD /dev/sda detected
cat: can't open '/sys/block/sdb/removable': No such file or directory
sh: mtd5: unknown operand
Create fw_env.config in /etc
Model name is ix2-ng
mdadm: cannot open /dev/sda1: No such device or address
cat: can't open '/sys/block/sda/sda1/size': No such file or directory
mdadm: No devices to examine
cat: can't open '/sys/block///size': No such file or directory
Valid Disk 1 in md0:
Valid Disk 2 in md0:
USB Device node is /dev/sdb1
Checking to see the if the reset button is presusb 1-1: configuration #1 chosen from 1 choice
sed or not
Starscsi2 : SCSI emulation for USB Mass Storage devices
ted
/dev/btns file does not exist creating it
Opened /dev/btns with fd 3
Checking status of reset button
Button Check 1:
The Button ID from drive is 2 push_cntr is 1 release_cntr is 0
Reset Button is pressed
Checking if there is an attached EMC Imager
scsi 2:0:0:0: Direct-Access JetFlash Transcend 2GB 8.07 PQ: 0 ANSI: 2
sd 2:0:0:0: Attached scsi generic sg1 type 0
sd 2:0:0:0: [sdb] 4100096 512-byte logical blocks: (2.09 GB/1.95 GiB)
sd 2:0:0:0: [sdb] Write Protect is off
sd 2:0:0:0: [sdb] Assuming drive cache: write through
sd 2:0:0:0: [sdb] Assuming drive cache: write through
sdb: sdb1
sd 2:0:0:0: [sdb] Assuming drive cache: write through
sd 2:0:0:0: [sdb] Attached SCSI removable disk
FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
Checking for pre-image script... none.
Image tar file found: /usb_drive/emctools/ix2-ng_images/*.tgz
Extract Image tar file.
upgrade.xml
zImage
zImage.md5
initrd
initrd.md5
config
config.md5
apps
apps.md5
oem
oem.md5
lvmsetarchive
sshdupd.py
sslcertupd.py
menu.lst
inittab
logrotate.conf
ix2-ng_SPI_copy_kernel_initrd
sslupd.py
enableatmosupgrade.py
Upgrade_USBShares.py
updateacl
zeroconf
apps is valid
config is valid
initrd is valid
zImage is valid
Found EMC Imager with apps and config image...
Started USB Imaging...
md: md0 stopped.
mdadm: stopped /dev/md0
mdadm: /dev/md0 not identified in config file.
---Mounting volume
mount: mounting /dev/md0_vg/BFDlv on sysroot/boot failed: No such file or directory
Going to do a full install
umount: cannot umount /sysroot/boot: Invalid argument
---Stop volumes
Volume group "md0_vg" not found
---Stop raid
md: md0 stopped.
mdadm: stopped /dev/md0
---destroy raid
mdadm: Couldn't open /dev/sda1 for write - not zeroing
---Prepping drive: sda
Error: Partition doesn't exist.
Error: Partition doesn't exist.
10000+0 records in
10000+0 records out
---Creating partition on /dev/sda
Information: You may need to update /etc/fstab.
Information: You may need to update /etc/fstab.
Information: You may need to update /etc/fstab.
---Starting raid
md: bind<sda1>
raid1: raid set md0 active with 1 out of 2 mirrors
md0: detected capacity change from 0 to 21474770944
mdadm: array /dev/md0 started.
---Creating volumes
md0: unknown partition table
Physical volume "/dev/md0" successfully created
Volume group "md0_vg" successfully created
Logical volume "BFDlv" created
---Formatting partitions
mke2fs 1.41.3 (12-Oct-2008)
ext2fs_check_if_mount: No such file or directory while determining whether /dev/md0_vg/BFDlv is mounted.
Filesystem label=
OS type: Linux
Block size=4096 (log=2)
Fragment size=4096 (log=2)
262144 inodes, 1048576 blocks
52428 blocks (5.00%) reserved for the super user
First data block=0
Maximum filesystem blocks=1073741824
32 block groups
32768 blocks per group, 32768 fragments per group
8192 inodes per group
Superblock backups stored on blocks:
32768, 98304, 163840, 229376, 294912, 819200, 884736
Writing inode tables: 0/32 1/32 2/32 3/32 4/32 5/32 6/32 7/32 8/32 9/32 10/32 11/32 12/32 13/32 14/32 15/32 16/32 17/32 18/32 19/32 20/32 21/32 22/32 23/32 24/32 25/32 26/32 27/32 28/32 29/32 30/32 31/32 done
Writing superblocks and filesystem accounting information: done
This filesystem will be automatically checked every 29 mounts or
180 days, whichever comes first. Use tune2fs -c or -i to override.
---Mounting volume
1 logical volume(s) in volume group "md0_vg" now active
---Copying system image files
Copied apps config and oem image
BusyBox v1.9.2 (2012-11-09 16:52:11 EST) multi-call binary
Usage: cp [OPTION]... SOURCE DEST
Copy SOURCE to DEST, or multiple SOURCE(s) to DIRECTORY
Options:
-a Same as -dpR
-d,-P Preserve links
-H,-L Dereference all symlinks (default)
-p Preserve file attributes if possible
-f Force overwrite
-i Prompt before overwrite
-R,-r Recurse directories
-l,-s Create (sym)links
BusyBox v1.9.2 (2012-11-09 16:52:11 EST) multi-call binary
Usage: cp [OPTION]... SOURCE DEST
Copy SOURCE to DEST, or multiple SOURCE(s) to DIRECTORY
Options:
-a Same as -dpR
-d,-P Preserve links
-H,-L Dereference all symlinks (default)
-p Preserve file attributes if possible
-f Force overwrite
-i Prompt before overwrite
-R,-r Recurse directories
-l,-s Create (sym)links
---Stop volumes
---Stop raid
md: md0 stopped.
md: unbind<sda1>
md: export_rdev(sda1)
mdadm: stopped /dev/md0
---Writing hidden sectors
5477+1 records in
5477+1 records out
5673+1 records in
5673+1 records out
Remove the temp folder.
DONE copying images
Imaging Successful. Please remove the USB drive before the next power on
USB/DOM device is sdb
cat: can't open '/sys/block/sdc/removable': No such file or directory
Drives are sd[a]
/dev/sda:
/dev/sda:
setting drive write-caching to 0 (off)
write-caching = 0 (off)
/dev/sda:
issuing standby command
Constructing root filesystem...
Bootstrapping ...
tmpfs: No value for mount option 'relatime'
mount: mounting none on / failed: Invalid argument
Initialization complete.
Freeing init memory: 140K
init started: BusyBox v1.9.2 (2012-11-09 16:52:11 EST)
starting pid 807, tty '': '/etc/init.d/rcS'
starting pid 810, tty '': 'umount'
BusyBox v1.9.2 (2012-11-09 16:52:11 EST) multi-call binary
Usage: umount [flags] FILESYSTEM|DIRECTORY
Unmount file systems
Options:
-r Try to remount devices as read-only if mount is busy
-l Lazy umount (detach filesystem)
-f Force umount (i.e., unreachable NFS server)
-D Do not free loop device (if a loop device has been used)
The system is going down NOW!
Sending SIGTERM to all processes
Sending SIGKILL to all processes
Requesting system poweroff
md: stopping all md devices.
sd 0:0:0:0: [sda] Synchronizing SCSI cache
Power down.
Лог первой загрузки:
=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2013.03.06 12:04:44 =~=~=~=~=~=~=~=~=~=~=~=
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__| ** ix2-spi ** ** uboot_ver:0.0.8 **
** MARVELL BOARD: DB-88F6282A-BP LE
U-Boot 1.1.4 (Oct 28 2011 - 15:18:22) Marvell version: 3.6.1 - EMC
U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CD5A0
Soc: 88F6282 A1 CPU running @ 1600Mhz L2 running @ 800Mhz
SysClock = 533Mhz , TClock = 200Mhz
DRAM (DDR3) CAS Latency = 7 tRP = 7 tRAS = 20 tRCD=7
DRAM CS[0] base 0x00000000 size 256MB
DRAM Total size 256MB 16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
Found ADT7473, program PWM1 ... OK
[1024kB@f8000000] Flash: 1 MB
Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (6)
Device 0 @ 0 0:
Model: ST250DM000-1BD141 Firm: KC45 Ser#: 9VYHEAE0
Type: Hard Disk
Supports 48-bit addressing
Capacity: 238475.1 MB = 232.8 GB (488397168 x 512)
CPU : Marvell Feroceon (Rev 1)
Streaming disabled
Write allocate disabled
USB 0: host mode
PEX 0: interface detected no Link.
PEX 1: interface detected no Link.
Net: egiga0 [PRIME]
Hit any key to stop autoboot: 3 2 1 0
Reset IDE:
Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (6)
Device 0 @ 0 0:
Model: ST250DM000-1BD141 Firm: KC45 Ser#: 9VYHEAE0
Type: Hard Disk
Supports 48-bit addressing
Capacity: 238475.1 MB = 232.8 GB (488397168 x 512)
IDE read: device 0 block # 2048, count 6144 ... 6144 blocks read: OK
IDE read: device 0 block # 8192, count 6144 ... 6144 blocks read: OK
## Booting image at 00040000 ...
Image Name: Linux-2.6.31.8
Created: 2012-10-04 20:59:31 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2804428 Bytes = 2.7 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
## Loading Ramdisk Image at 00900000 ...
Image Name:
Created: 2012-11-09 21:52:49 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 2904981 Bytes = 2.8 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Starting kernel ...
Linux version 2.6.31.8 (soho@bsoho080.lss.emc.com) (gcc version 4.3.2 (Sourcery G++ Lite 2008q3-72) ) Thu Oct 4 16:59:24 EDT 2012 v0.0.9 Thu Oct 4 16:59:24 EDT 2012
CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977
CPU: VIVT data cache, VIVT instruction cache
Machine: Feroceon-KW
Using UBoot passing parameters structure
Memory policy: ECC disabled, Data cache writeback
Built 1 zonelists in Zone order, mobility grouping off. Total pages: 64960
Kernel command line: console=ttyS0,115200 root=/dev/ram0 mtdparts=spi_flash:0x7e000@0(u-boot),0x1000@0x7f000(env),0x1000@0x7e000(env2) :::DB88FXX81:eth0:none
PID hash table entries: 1024 (order: 10, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 256MB = 256MB total
Memory: 243968KB available (5196K code, 325K data, 140K init, 0K highmem)
Hierarchical RCU implementation.
NR_IRQS:128
Console: colour dummy device 80x30
Calibrating delay loop... 1589.24 BogoMIPS (lpj=7946240)
Security Framework initialized
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
xor: measuring software checksum speed
arm4regs : 1446.000 MB/sec
8regs : 1096.000 MB/sec
32regs : 1070.800 MB/sec
xor: using function: arm4regs (1446.000 MB/sec)
NET: Registered protocol family 16
Feroceon L2: Enabling L2
Feroceon L2: Cache support initialised.
CPU Interface
-------------
SDRAM_CS0 ....base 00000000, size 256MB
SDRAM_CS1 ....disable
SDRAM_CS2 ....disable
SDRAM_CS3 ....disable
PEX0_MEM ....base e0000000, size 128MB
PEX0_IO ....base f2000000, size 1MB
PEX1_MEM ....base e8000000, size 128MB
PEX1_IO ....base f2100000, size 1MB
INTER_REGS ....base f1000000, size 1MB
NFLASH_CS ....base fa000000, size 2MB
SPI_CS ....base f4000000, size 16MB
BOOT_ROM_CS ....no such
DEV_BOOTCS ....no such
CRYPT_ENG ....base f0000000, size 2MB
Marvell Development Board (LSP Version KW_LSP_5.1.3_patch25)-- DB-88F6282A-BP Soc: 88F6282 A1 LE
Detected Tclk 200000000 and SysClk 533333333
MV Buttons Device Load
Marvell USB EHCI Host controller #0: c8040740
PEX0 interface detected no Link.
PEX1 interface detected no Link.
PCI: bus0: Fast back to back transfers enabled
PCI: bus1: Fast back to back transfers enabled
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
raid6: int32x1 133 MB/s
raid6: int32x2 156 MB/s
raid6: int32x4 164 MB/s
raid6: int32x8 126 MB/s
raid6: using algorithm int32x4 (164 MB/s)
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
NET: Registered protocol family 1
Trying to unpack rootfs image as initramfs...
rootfs image is not initramfs (no cpio magic); looks like an initrd
Freeing initrd memory: 2836K
rtc mv_rtc: rtc core: registered kw-rtc as rtc0
RTC registered
XOR registered 4 channels
XOR 2nd invalidate WA enabled
cesadev_init(c000edd4)
mvCesaInit: sessions=640, queue=64, pSram=f0000000
MV Buttons Driver Load
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
squashfs: version 4.0 (2009/01/31) Phillip Lougher
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
SGI XFS with ACLs, security attributes, large block/inode numbers, no debug enabled
SGI XFS Quota Management subsystem
msgmni has been set to 482
alg: No test for cipher_null (cipher_null-generic)
alg: No test for ecb(cipher_null) (ecb-cipher_null)
alg: No test for digest_null (digest_null-generic)
alg: No test for compress_null (compress_null-generic)
alg: No test for stdrng (krng)
alg: No test for hmac(digest_null) (hmac(digest_null-generic))
async_tx: api initialized (sync-only)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
io scheduler noop registered
io scheduler anticipatory registered (default)
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xf1012100 (irq = 34) is a 16550A
console [ttyS0] enabled
brd: module loaded
loop: module loaded
Integrated Sata device found
IRQ 21/mvSata: IRQF_DISABLED is not guaranteed on shared IRQs
scsi0 : Marvell SCSI to SATA adapter
scsi1 : Marvell SCSI to SATA adapter
scsi 0:0:0:0: Direct-Access Seagate ST250DM000-1BD14 KC45 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] Sector size 0 reported, assuming 512.
sd 0:0:0:0: [sda] 488397168 512-byte logical blocks: (250 GB/232 GiB)
sd 0:0:0:0: [sda] 0-byte physical blocks
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 0:0:0:0: [sda] Write Protect is off
Loading Marvell Ethernet Driver:
o Cached descriptors in DRAM
o DRAM SW cache-coherency
o 2 Giga ports supported
o Single RX Queue support - ETH_DEF_RXQ=0
o Single TX Queue support - ETH_DEF_TXQ=0
o TCP segmentation offload (TSO) supported
o Large Receive offload (LRO) supported
o Receive checksum offload supported
o Transmit checksum offload supported
o Network Fast Processing (Routing) supported - (Disabled)
o Proc tool API enabled
o SKB Reuse supported - (Disabled)
o SKB Recycle supported - (Disabled)
o Rx descripors: q0=256
o Tx descripors: q0=532
o Loading network interface(s):
o register under mv88fx_eth platform
o eth0, ifindex = 2, GbE port = 0
Warning: Giga 1 is Powered Off
mvFpRuleDb (c0928000): 2048 entries, 8192 bytes
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA
sd 0:0:0:0: [sda] Sector size 0 reported, assuming 512.
SPI Serial flash detected @ 0xf4000000, 1024KB (256sec x 4KB)
3 cmdlinepart partitions found on MTD device spi_flash
Creating 3 MTD partitions on "spi_flash":
0x000000000000-0x00000007e000 : "u-boot"
0x00000007f000-0x000000080000 : "env"
0x00000007e000-0x00000007f000 : "env2"
sda:Using Hamming 1-bit ECC for NAND device
No NAND device found!!!
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci_marvell ehci_marvell.70059: Marvell Orion EHCI
ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus number 1
ehci_marvell ehci_marvell.70059: irq 19, io base 0xf1050100
sda1
sd 0:0:0:0: [sda] Sector size 0 reported, assuming 512.
sd 0:0:0:0: [sda] Attached SCSI disk
ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
uhci_hcd: USB Universal Host Controller Interface driver
usbcore: registered new interface driver usblp
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver ums-datafab
usbcore: registered new interface driver ums-freecom
usbcore: registered new interface driver ums-jumpshot
usbcore: registered new interface driver ums-sddr09
usbcore: registered new interface driver ums-sddr55
usbcore: registered new interface driver ums-usbat
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
adt7473 0-002e: adt7473 chip found
iBoard_model 2
md: linear personality registered for level -1
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
md: raid10 personality registered for level 10
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
dm_crypt using the OCF package.
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
TCP cubic registered
NET: Registered protocol family 17
NET: Registered protocol family 5
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
rtc mv_rtc: setting system clock to 2013-03-06 03:04:59 UTC (1362539099)
md: Waiting for all devices to be available before autodetect
md: If you don't use raid, use raid=noautodetect
md: Autodetecting RAID arrays.
md: Scanned 1 and added 1 devices.
md: autorun ...
md: considering sda1 ...
md: adding sda1 ...
md: created md0
md: bind<sda1>
md: running: <sda1>
raid1: raid set md0 active with 1 out of 2 mirrors
md0: detected capacity change from 0 to 21474770944
md: ... autorun DONE.
RAMDISK: gzip image found at block 0
VFS: Mounted root (ext2 filesystem) on device 1:0.
Looking for shell in cmdline: console=ttyS0,115200 root=/dev/ram0 mtdparts=spi_flash:0x7e000@0(u-boot),0x1000@0x7f000(env),0x1000@0x7e000(env2) :::DB88FXX81:eth0:none
Make node for mtd devices
HDD /dev/sda detected
cat: can't open '/sys/block/sdb/removable': No such file or directory
sh: mtd5: unknown operand
Create fw_env.config in /etc
Model name is ix2-ng
UUID_1 = 8018a9b4:8ff61352:c88cda7d:8f205803, size = 41943041
mdadm: No devices to examine
cat: can't open '/sys/block///size': No such file or directory
Valid Disk 1 in md0: /dev/sda1
Valid Disk 2 in md0:
USB Device node is /dev/sdb1
Checking to see the if the reset button is pressed or not
Started
/dev/btns file does not exist creating it
Opened /dev/btns with fd 3
Checking status of reset button
Button Check 1:
The Button ID from drive is 2 push_cntr is 0 release_cntr is 0
Button Check 2:
The Button ID from drive is 2 push_cntr is 0 release_cntr is 0
Button Check 3:
The Button ID from drive is 2 push_cntr is 0 release_cntr is 0
Button Check 4:
The Button ID from drive is 2 push_cntr is 0 release_cntr is 0
Button Check 5:
The Button ID from drive is 2 push_cntr is 0 release_cntr is 0
Button Check 6:
The Button ID from drive is 2 push_cntr is 0 release_cntr is 0
Button Check 7:
The Button ID from drive is 2 push_cntr is 0 release_cntr is 0
Button Check 8:
The Button ID from drive is 2 push_cntr is 0 release_cntr is 0
Button Check 9:
The Button ID from drive is 2 push_cntr is 0 release_cntr is 0
Button Check 10:
The Button ID from drive is 2 push_cntr is 0 release_cntr is 0
Reset Button is NOT pressed
Checking for valid image on system
md0: unknown partition table
md: md0 stopped.
md: unbind<sda1>
md: export_rdev(sda1)
mdadm: stopped /dev/md0
md: md0 stopped.
md: bind<sda1>
raid1: raid set md0 active with 1 out of 2 mirrors
md0: detected capacity change from 0 to 21474770944
mdadm: /dev/md0 has been started with 1 drive (out of 2).
md0: unknown partition table
1 logical volume(s) in volume group "md0_vg" now active
Found Valid EMC Image in disk...
Mounting apps image...
Mounting config image...
Check config filesystem
e2fsck 1.41.3 (12-Oct-2008)
ext2fs_check_if_mount: No such file or directory while determining whether /dev/loop1 is mounted.
No need to create fw_env.config
Create fw_env.config in /etc
Clean up the memory...
Constructing root filesystem...
Bootstrapping ...
rootdir=/
table='/usr/local/cfg/device_table.txt'
makedevs: line 42: chown failed for /bin/busybox: Read-only file system
makedevs: line 49: regular file '/usr/share/udhcpc/default.script' does not exist: No such file or directory
Loading ext3...
FATAL: Module ext3 not found.
Loading isofs...
Loading ntfs...
FATAL: Module ntfs not found.
Loading udf...
Loading ufsd...
ufsd: module license 'Commercial product' taints kernel.
Disabling lock debugging due to kernel taint
ufsd: driver 8.5 (Nov 2 2012 09:59:10) LBD=ON with delayalloc with ioctl loaded at bf029000
NTFS support included
Hfs+/HfsX support included
Built for: EMC_ix2_2Initialization complete.
Freeing init memory: 140K
INIT: version 2.86 booting
Running file /etc/init.d/rcS
Running file /etc/init.d/rc
Running file /etc/rcS.d/S01glibc.sh
Running file /etc/rcS.d/S02hostname.sh
Running file /etc/rcS.d/S02mountkernfs.sh
Running file /etc/rcS.d/S04mountdevsubfs.sh
Running file /etc/rcS.d/S05bootlogd
Running file /etc/rcS.d/S07hdparm
Setting parameters of disc: (none).
Running file /etc/rcS.d/S08hwclockfirst.sh
Setting the system clock.
Running file /etc/rcS.d/S11hwclock.sh
Setting the system clock.
Running file /etc/rcS.d/S12mtab.sh
mount: according to mtab, tmpfs is already mounted on /lib/init/rw
Running file /etc/rcS.d/S18ifupdown-clean
Cleaning up ifupdown....
Running file /etc/rcS.d/S20module-init-tools
Loading kernel modules...done.
Running file /etc/rcS.d/S26lvm2
Setting up LVM Volume Groups Reading all physical volumes. This may take a while...
Found volume group "md0_vg" using metadata type lvm2
1 logical volume(s) in volume group "md0_vg" now active
.
Running file /etc/rcS.d/S30checkfs.sh
Checking file systems...fsck 1.41.3 (12-Oct-2008)
done.
Running file /etc/rcS.d/S30procps
Setting kernel variables (/etc/sysctl.conf)...Running file /etc/rcS.d/S35mountall.sh
Mounting local filesystems...done.
Activating swapfile swap...done.
Running file /etc/rcS.d/S36mountall-bootclean.sh
Running file /etc/rcS.d/S37mountoverflowtmp
dhclient host identical
Running file /etc/rcS.d/S39ifupdown
Setting up networking....
Running file /etc/rcS.d/S40networking
Configuring network interfaces...done.
Running file /etc/rcS.d/S43portmap
Starting portmap daemon....
Running file /etc/rcS.d/S45mountnfs.sh
Running file /etc/rcS.d/S46mountnfs-bootclean.sh
Running file /etc/rcS.d/S55bootmisc.sh
Running file /etc/rcS.d/S55urandom
Running file /etc/rcS.d/S99stop-bootlogd-single
INIT: cannot execute "
INIT: Entering runlevel: 2
Running file /etc/init.d/rc
Running file /etc/rc2.d/S10rsyslog
Starting enhanced syslogd: rsyslogd.
Running file /etc/rc2.d/S12dbus
chown: invalid user: `messagebus'
Running file /etc/rc2.d/S20rsync
Running file /etc/rc2.d/S20smartmontools
Not starting S.M.A.R.T. daemon smartd, disabled via /etc/default/smartmontools [33m(warning). [39;49m
Running file /etc/rc2.d/S20sysfsutils
Setting sysfs variables....
Running file /etc/rc2.d/S23ntp
Starting NTP server: ntpdRunning file /etc/rc2.d/S25bluetooth
Starting bluetooth: hcidBluetooth: Core ver 2.15
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.13
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM ver 1.11
.
Starting netplugd...
eth0: link down
eth0: started
eth0: link up, full duplex, speed 1 Gbps
Generating RSA Key...
Generating public/private rsa1 key pair.
Your identification has been saved in /etc/ssh/ssh_host_key.
Your public key has been saved in /etc/ssh/ssh_host_key.pub.
The key fingerprint is:
57:51:74:95:9f:8a:9f:25:73:ab:5f:8d:51:4f:e8:9d
The key's randomart image is:
+--[RSA1 2048]----+
| .oo =|
| . + |
| . . =|
| . . =+|
| S . . +Eo|
| . . + =.|
| . B +|
| o ..|
| .o. |
+-----------------+
Starting sshd: OK
hostnamed begin to start...
Name now registered and active
hostnamed finished
IP obtaining in progress...
IP obtained
Starting executord
Done.
Running file /etc/rc2.d/S99rc.local
Running file /etc/rc2.d/S99rmnologin
Running file /etc/rc2.d/S99stop-bootlogd
Running file /etc/init.d/bootlogd
Welcome to CenterPoint.
ix2 login: md: bind<sda2>
md1: detected capacity change from 0 to 228550901760
md1: unknown partition table
XFS mounting filesystem dm-1
Welcome to CenterPoint.
ix2 login:
Welcome to CenterPoint.
ix2 login:
Welcome to CenterPoint.
ix2 login:
Welcome to CenterPoint.
ix2 login:
Welcome to CenterPoint.
ix2 login: admiAdding 524280k swap on /mnt/system/swapfile. Priority:-1 extents:4 across:8418776k
n
Password: XFS mounting filesystem dm-2
Login incorrect
ix2 login: root
Password:
root@ix2:/# uname -a
Linux ix2 2.6.31.8 Thu Oct 4 16:59:24 EDT 2012 v0.0.9 Thu Oct 4 16:59:24 EDT 2012 armv5tel GNU/Linux
root@ix2:/#
Broadcast message from root@ix2 (Tue Mar 5 19:08:56 2013):
The system is going down for system halt NOW!
INIT:
INIT: Running file /etc/init.d/rc
Stopping iSCSI-SCST target service: failed.
Removing iSCSI-SCST target modules: succeeded.
Running file /etc/rc0.d/K20rsync
Stopping rsync daemon: rsync.
Running file /etc/rc0.d/K20smartmontools
Stopping S.M.A.R.T. daemon: smartd.
Running file /etc/rc0.d/K23ntp
Stopping NTP server: ntpd.
Running file /etc/rc0.d/K25hwclock.sh
Saving the system clock.
Running file /etc/rc0.d/K25mdadm
Running file /etc/rc0.d/K63mountoverflowtmp
Running file /etc/rc0.d/K74bluetooth
Stopping bluetooth: hcid.
Running file /etc/rc0.d/K90rsyslog
Stopping enhanced syslogd: rsyslogd.
Running file /etc/rc0.d/S20sendsigs
Asking all remaining processes to terminate...mDNSResponder: mDNSResponder (Engineering Build) (Oct 4 2012 17:14:24) stopping
mDNSResponder: mDNS_FinalExit failed to send goodbye for: 0006CBD8 01 29 _workstation._tcp.local. PTR ix2._workstation._tcp.local.
mDNSResponder: mDNS_FinalExit failed to send goodbye for: 0006E1F8 01 32 _LifeLineDevice._tcp.local. PTR ix2._LifeLineDevice._tcp.local.
done.
Killing all remaining processes... [31mfailed. [39;49m
Running file /etc/rc0.d/S30urandom
Running file /etc/rc0.d/S31umountnfs.sh
Running file /etc/rc0.d/S32portmap
Stopping portmap daemon....
Running file /etc/rc0.d/S35networking
Deconfiguring network interfaces...There is already a pid file /var/run/dhclient.eth0.pid with pid 1147
removed stale PID file
Internet Systems Consortium DHCP Client V3.1.1
Copyright 2004-2008 Internet Systems Consortium.
All rights reserved.
For info, please visit http://www.isc.org/sw/dhcp/
Listening on LPF/eth0/00:d0:b8:1d:78:bc
Sending on LPF/eth0/00:d0:b8:1d:78:bc
Sending on Socket/fallback
DHCPRELEASE on eth0 to 10.100.106.4 port 67
eth0: stopped
done.
Running file /etc/rc0.d/S36ifupdown
Running file /etc/init.d/ifupdown-clean
Cleaning up ifupdown....
Running file /etc/rc0.d/S50lvm2
Shutting down LVM Volume Groups Can't deactivate volume group "192eefdb_vg" with 1 open logical volume(s)
Can't deactivate volume group "md0_vg" with 2 open logical volume(s)
[31mfailed! [39;49m
Running file /etc/rc0.d/S60mdadm-raid
md: md1 still in use.
md: md0 still in use.
md: md1 still in use.
md: md0 still in use.
Stopping MD array md1... [31mfailed (busy). [39;49m
Stopping MD array md0... [31mfailed (busy). [39;49m
Running file /etc/rc0.d/S90halt
Will now halt.
INIT: cannot execute "/sbin/addLog"
INIT: no more processes left in this runlevel
0 logical volume(s) in volume group "192eefdb_vg" now active
md: md0 still in use.
md: md1 stopped.
md: unbind<sda2>
md: export_rdev(sda2)
Pivot root to /shutdown in RAM
0 logical volume(s) in volume group "md0_vg" now active
md: md0 stopped.
md: unbind<sda1>
md: export_rdev(sda1)
md: md1 stopped.
Drives are sd[a]
/dev/sda:
/dev/sda:
setting drive write-caching to 0 (off)
write-caching = 0 (off)
/dev/sda:
issuing standby command
Mount table prior to shutdown:
rootfs on / type rootfs (rw)
none on /sysroot type tmpfs (rw,relatime,size=51200k,nr_inodes=30878)
tmpfs on / type tmpfs (rw,relatime)
proc on /proc type proc (rw,relatime)
sysfs on /sys type sysfs (rw,relatime)
Execute shutdown command: poweromd: stopping all md devices.
ff -f
sd 0:0:0:0: [sda] Synchronizing SCSI cache
Power down.
1 0
Reset IDE:
Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (6)
Device 0 @ 0 0:
Model: Hitachi HUA723030ALA640 Firm: MKAOA5C0 Ser#: MK0331YHGY11KA
Type: Hard Disk
Supports 48-bit addressing
Capacity: 764436.4 MB = 746.5 GB (1565565872 x 512)
[0 1 0]: Enable DMA mode (6)
Device 1 @ 0 1:
Model: Hitachi HUA723030ALA640 Firm: MKAOA5C0 Ser#: MK0331YHH2N46A
Type: Hard Disk
Supports 48-bit addressing
Capacity: 764436.4 MB = 746.5 GB (1565565872 x 512)
IDE read: device 0 block # 2048, count 6144 ... 6144 blocks read: OK
IDE read: device 0 block # 8192, count 6144 ... 6144 blocks read: OK
## Booting image at 00040000 ...
Image Name: Linux-2.6.31.8
Created: 2012-10-04 20:59:31 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2804428 Bytes = 2.7 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
## Loading Ramdisk Image at 00900000 ...
Image Name:
Created: 2012-11-09 21:52:49 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 2904981 Bytes = 2.8 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Starting kernel ...
Linux version 2.6.31.8 (soho@bsoho080.lss.emc.com) (gcc version 4.3.2 (Sourcery G++ Lite 2008q3-72) ) Thu Oct 4 16:59:24 EDT 2012 v0.0.9 Thu Oct 4 16:59:24 EDT 2012
CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977
CPU: VIVT data cache, VIVT instruction cache
Machine: Feroceon-KW
Using UBoot passing parameters structure
Memory policy: ECC disabled, Data cache writeback
Built 1 zonelists in Zone order, mobility grouping off. Total pages: 64960
Kernel command line: console=ttyS0,115200 root=/dev/ram0 mtdparts=spi_flash:0x7e000@0(u-boot),0x1000@0x7f000(env),0x1000@0x7e000(env2) :::DB88FXX81:eth0:none
PID hash table entries: 1024 (order: 10, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 256MB = 256MB total
Memory: 243968KB available (5196K code, 325K data, 140K init, 0K highmem)
Hierarchical RCU implementation.
NR_IRQS:128
Console: colour dummy device 80x30
Calibrating delay loop... 1589.24 BogoMIPS (lpj=7946240)
Security Framework initialized
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
xor: measuring software checksum speed
arm4regs : 1446.000 MB/sec
8regs : 1096.000 MB/sec
32regs : 1071.200 MB/sec
xor: using function: arm4regs (1446.000 MB/sec)
NET: Registered protocol family 16
Feroceon L2: Enabling L2
Feroceon L2: Cache support initialised.
CPU Interface
-------------
SDRAM_CS0 ....base 00000000, size 256MB
SDRAM_CS1 ....disable
SDRAM_CS2 ....disable
SDRAM_CS3 ....disable
PEX0_MEM ....base e0000000, size 128MB
PEX0_IO ....base f2000000, size 1MB
PEX1_MEM ....base e8000000, size 128MB
PEX1_IO ....base f2100000, size 1MB
INTER_REGS ....base f1000000, size 1MB
NFLASH_CS ....base fa000000, size 2MB
SPI_CS ....base f4000000, size 16MB
BOOT_ROM_CS ....no such
DEV_BOOTCS ....no such
CRYPT_ENG ....base f0000000, size 2MB
Marvell Development Board (LSP Version KW_LSP_5.1.3_patch25)-- DB-88F6282A-BP Soc: 88F6282 A1 LE
Detected Tclk 200000000 and SysClk 533333333
MV Buttons Device Load
Marvell USB EHCI Host controller #0: c8040740
PEX0 interface detected no Link.
PEX1 interface detected no Link.
PCI: bus0: Fast back to back transfers enabled
PCI: bus1: Fast back to back transfers enabled
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
raid6: int32x1 133 MB/s
raid6: int32x2 156 MB/s
raid6: int32x4 164 MB/s
raid6: int32x8 126 MB/s
raid6: using algorithm int32x4 (164 MB/s)
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
NET: Registered protocol family 1
Trying to unpack rootfs image as initramfs...
rootfs image is not initramfs (no cpio magic); looks like an initrd
Freeing initrd memory: 2836K
rtc mv_rtc: rtc core: registered kw-rtc as rtc0
RTC registered
XOR registered 4 channels
XOR 2nd invalidate WA enabled
cesadev_init(c000edd4)
mvCesaInit: sessions=640, queue=64, pSram=f0000000
MV Buttons Driver Load
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
squashfs: version 4.0 (2009/01/31) Phillip Lougher
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
SGI XFS with ACLs, security attributes, large block/inode numbers, no debug enabled
SGI XFS Quota Management subsystem
msgmni has been set to 482
alg: No test for cipher_null (cipher_null-generic)
alg: No test for ecb(cipher_null) (ecb-cipher_null)
alg: No test for digest_null (digest_null-generic)
alg: No test for compress_null (compress_null-generic)
alg: No test for stdrng (krng)
alg: No test for hmac(digest_null) (hmac(digest_null-generic))
async_tx: api initialized (sync-only)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
io scheduler noop registered
io scheduler anticipatory registered (default)
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xf1012100 (irq = 34) is a 16550A
console [ttyS0] enabled
brd: module loaded
loop: module loaded
Integrated Sata device found
IRQ 21/mvSata: IRQF_DISABLED is not guaranteed on shared IRQs
scsi0 : Marvell SCSI to SATA adapter
scsi1 : Marvell SCSI to SATA adapter
scsi 0:0:0:0: Direct-Access Hitachi HUA723030ALA640 MKAO PQ: 0 ANSI: 5
scsi 1:0:0:0: Direct-Access Hitachi HUA723030ALA640 MKAO PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] Sector size 0 reported, assuming 512.
sd 0:0:0:0: [sda] 5860533168 512-byte logical blocks: (3.00 TB/2.72 TiB)
sd 0:0:0:0: [sda] 0-byte physical blocks
sd 1:0:0:0: [sdb] Sector size 0 reported, assuming 512.
sd 1:0:0:0: [sdb] 5860533168 512-byte logical blocks: (3.00 TB/2.72 TiB)
sd 1:0:0:0: [sdb] 0-byte physical blocks
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 1:0:0:0: Attached scsi generic sg1 type 0
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA
sd 0:0:0:0: [sda] Sector size 0 reported, assuming 512.
sd 1:0:0:0: [sdb] Write Protect is off
Loading Marvell Ethernet Driver:
o Cached descriptors in DRAM
o DRAM SW cache-coherency
o 2 Giga ports supported
o Single RX Queue support - ETH_DEF_RXQ=0
o Single TX Queue support - ETH_DEF_TXQ=0
o TCP segmentation offload (TSO) supported
o Large Receive offload (LRO) supported
o Receive checksum offload supported
o Transmit checksum offload supported
o Network Fast Processing (Routing) supported - (Disabled)
o Proc tool API enabled
o SKB Reuse supported - (Disabled)
o SKB Recycle supported - (Disabled)
o Rx descripors: q0=256
o Tx descripors: q0=532
o Loading network interface(s):
o register under mv88fx_eth platform
o eth0, ifindex = 2, GbE port = 0
Warning: Giga 1 is Powered Off
mvFpRuleDb (c0b4a000): 2048 entries, 8192 bytes
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
sda:
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, supports DPO and FUA
sd 1:0:0:0: [sdb] Sector size 0 reported, assuming 512.
SPI Serial flash detected @ 0xf4000000, 1024KB (256sec x 4KB)
3 cmdlinepart partitions found on MTD device spi_flash
Creating 3 MTD partitions on "spi_flash":
0x000000000000-0x00000007e000 : "u-boot"
0x00000007f000-0x000000080000 : "env"
0x00000007e000-0x00000007f000 : "env2"
sdb:Using Hamming 1-bit ECC for NAND device
No NAND device found!!!
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci_marvell ehci_marvell.70059: Marvell Orion EHCI
ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus number 1
sda1 sda2
sd 0:0:0:0: [sda] Sector size 0 reported, assuming 512.
sd 0:0:0:0: [sda] Attached SCSI disk
ehci_marvell ehci_marvell.70059: irq 19, io base 0xf1050100
sdb1
sd 1:0:0:0: [sdb] Sector size 0 reported, assuming 512.
ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
sd 1:0:0:0: [sdb] Attached SCSI disk
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
uhci_hcd: USB Universal Host Controller Interface driver
usbcore: registered new interface driver usblp
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver ums-datafab
usbcore: registered new interface driver ums-freecom
usbcore: registered new interface driver ums-jumpshot
usbcore: registered new interface driver ums-sddr09
usbcore: registered new interface driver ums-sddr55
usbcore: registered new interface driver ums-usbat
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
adt7473 0-002e: adt7473 chip found
iBoard_model 2
md: linear personality registered for level -1
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
md: raid10 personality registered for level 10
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
dm_crypt using the OCF package.
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
TCP cubic registered
NET: Registered protocol family 17
NET: Registered protocol family 5
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
rtc mv_rtc: setting system clock to 2013-03-06 03:15:47 UTC (1362539747)
md: Waiting for all devices to be available before autodetect
md: If you don't use raid, use raid=noautodetect
md: Autodetecting RAID arrays.
md: Scanned 1 and added 1 devices.
md: autorun ...
md: considering sda1 ...
md: adding sda1 ...
md: created md0
md: bind<sda1>
md: running: <sda1>
raid1: raid set md0 active with 1 out of 2 mirrors
md0: detected capacity change from 0 to 21474770944
md: ... autorun DONE.
RAMDISK: gzip image found at block 0
VFS: Mounted root (ext2 filesystem) on device 1:0.
Looking for shell in cmdline: console=ttyS0,115200 root=/dev/ram0 mtdparts=spi_flash:0x7e000@0(u-boot),0x1000@0x7f000(env),0x1000@0x7e000(env2) :::DB88FXX81:eth0:none
Make node for mtd devices
HDD /dev/sda detected
HDD /dev/sdb detected
sh: mtd5: unknown operand
Create fw_env.config in /etc
Model name is ix2-ng
UUID_1 = 97bfab09:a493d4ee:9f6f6ebd:21db0b1f, size = 41943041
Valid Disk 1 in md0: /dev/sda1
Valid Disk 2 in md0:
USB Device node is /dev/sdc1
Checking to see the if the reset button is pressed or not
Started
/dev/btns file does not exist creating it
Opened /dev/btns with fd 3
Checking status of reset button
Button Check 1:
The Button ID from drive is 2 push_cntr is 0 release_cntr is 0
Button Check 2:
The Button ID from drive is 2 push_cntr is 0 release_cntr is 0
Button Check 3:
The Button ID from drive is 2 push_cntr is 0 release_cntr is 0
Button Check 4:
The Button ID from drive is 2 push_cntr is 0 release_cntr is 0
Button Check 5:
The Button ID from drive is 2 push_cntr is 0 release_cntr is 0
Button Check 6:
The Button ID from drive is 2 push_cntr is 0 release_cntr is 0
Button Check 7:
The Button ID from drive is 2 push_cntr is 0 release_cntr is 0
Button Check 8:
The Button ID from drive is 2 push_cntr is 0 release_cntr is 0
Button Check 9:
The Button ID from drive is 2 push_cntr is 0 release_cntr is 0
Button Check 10:
The Button ID from drive is 2 push_cntr is 0 release_cntr is 0
Reset Button is NOT pressed
Checking for valid image on system
md0: unknown partition table
md: md0 stopped.
md: unbind<sda1>
md: export_rdev(sda1)
mdadm: stopped /dev/md0
md: md0 stopped.
md: bind<sda1>
raid1: raid set md0 active with 1 out of 2 mirrors
md0: detected capacity change from 0 to 21474770944
mdadm: /dev/md0 has been started with 1 drive (out of 2).
md0: unknown partition table
2 logical volume(s) in volume group "md0_vg" now active
Found Valid EMC Image in disk...
Mounting apps image...
Mounting config image...
Check config filesystem
e2fsck 1.41.3 (12-Oct-2008)
ext2fs_check_if_mount: No such file or directory while determining whether /dev/loop1 is mounted.
No need to create fw_env.config
No need to create fw_env.config
Clean up the memory...
Constructing root filesystem...
Bootstrapping ...
rootdir=/
table='/usr/local/cfg/device_table.txt'
makedevs: line 42: chown failed for /bin/busybox: Read-only file system
makedevs: line 49: regular file '/usr/share/udhcpc/default.script' does not exist: No such file or directory
warning: can't open /etc/mtab: No such file or directory
Loading ext3...
FATAL: Module ext3 not found.
Loading isofs...
Loading ntfs...
FATAL: Module ntfs not found.
Loading udf...
Loading ufsd...
ufsd: module license 'Commercial product' taints kernel.
Disabling lock debugging due to kernel taint
ufsd: driver 8.5 (Nov 2 2012 09:59:10) LBD=ON with delayalloc with ioctl loaded at bf029000
NTFS support included
Hfs+/HfsX support included
Built for: EMC_ix2_2Initialization complete.
Freeing init memory: 140K
INIT: version 2.86 booting
Running file /etc/init.d/rcS
Running file /etc/init.d/rc
Running file /etc/rcS.d/S01glibc.sh
Running file /etc/rcS.d/S02hostname.sh
Running file /etc/rcS.d/S02mountkernfs.sh
Running file /etc/rcS.d/S04mountdevsubfs.sh
Running file /etc/rcS.d/S05bootlogd
Running file /etc/rcS.d/S07hdparm
Setting parameters of disc: (none).
Running file /etc/rcS.d/S08hwclockfirst.sh
Setting the system clock.
Running file /etc/rcS.d/S11hwclock.sh
Setting the system clock.
Running file /etc/rcS.d/S12mtab.sh
mount: according to mtab, tmpfs is already mounted on /lib/init/rw
Running file /etc/rcS.d/S18ifupdown-clean
Cleaning up ifupdown....
Running file /etc/rcS.d/S20module-init-tools
Loading kernel modules...done.
Running file /etc/rcS.d/S26lvm2
Setting up LVM Volume Groups Reading all physical volumes. This may take a while...
Found volume group "md0_vg" using metadata type lvm2
2 logical volume(s) in volume group "md0_vg" now active
.
Running file /etc/rcS.d/S30checkfs.sh
Checking file systems...fsck 1.41.3 (12-Oct-2008)
done.
Running file /etc/rcS.d/S30procps
Setting kernel variables (/etc/sysctl.conf)...Running file /etc/rcS.d/S35mountall.sh
Mounting local filesystems...done.
Activating swapfile swap...done.
Running file /etc/rcS.d/S36mountall-bootclean.sh
Running file /etc/rcS.d/S37mountoverflowtmp
Running file /etc/rcS.d/S39ifupdown
Setting up networking....
Running file /etc/rcS.d/S40networking
Configuring network interfaces...done.
Running file /etc/rcS.d/S43portmap
Starting portmap daemon....
Running file /etc/rcS.d/S45mountnfs.sh
Running file /etc/rcS.d/S46mountnfs-bootclean.sh
Running file /etc/rcS.d/S55bootmisc.sh
Running file /etc/rcS.d/S55urandom
Running file /etc/rcS.d/S99stop-bootlogd-single
INIT: cannot execute "
INIT: Entering runlevel: 2
Running file /etc/init.d/rc
Running file /etc/rc2.d/S10rsyslog
Starting enhanced syslogd: rsyslogd.
Running file /etc/rc2.d/S12dbus
chown: invalid user: `messagebus'
Running file /etc/rc2.d/S20rsync
Running file /etc/rc2.d/S20smartmontools
Not starting S.M.A.R.T. daemon smartd, disabled via /etc/default/smartmontools [33m(warning). [39;49m
Running file /etc/rc2.d/S20sysfsutils
Setting sysfs variables....
Running file /etc/rc2.d/S23ntp
Starting NTP server: ntpdRunning file /etc/rc2.d/S25bluetooth
Starting bluetooth: hcidBluetooth: Core ver 2.15
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.13
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM ver 1.11
.
Starting netplugd...
eth0: link down
eth0: started
eth0: link up, full duplex, speed 1 Gbps
ln: creating symbolic link `/etc/samba/smb.conf': File exists
Starting sshd: OK
hostnamed begin to start...
hostnamed finished
IP obtaining in progress...
IP obtained
Starting executord
Done.
Running file /etc/rc2.d/S99rc.local
Running file /etc/rc2.d/S99rmnologin
Running file /etc/rc2.d/S99stop-bootlogd
Running file /etc/init.d/bootlogd
Welcome to CenterPoint.
ix2 login: md: md1 stopped.
md: bind<sda2>
md1: detected capacity change from 0 to 2979084500992
md1: unknown partition table
XFS mounting filesystem dm-1
XFS mounting filesystem dm-2
Adding 524280k swap on /mnt/system/swapfile. Priority:-1 extents:4 across:4633812k
md: bind<sdb1>
RAID1 conf printout:
--- wd:1 rd:2
disk 0, wo:0, o:1, dev:sda1
disk 1, wo:1, o:1, dev:sdb1
md: recovery of RAID array md0
md: minimum _guaranteed_ speed: 1000 KB/sec/disk.
md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for recovery.
md: using 128k window, over a total of 20971456 blocks.
md: md0: recovery done.
RAID1 conf printout:
--- wd:2 rd:2
disk 0, wo:0, o:1, dev:sda1
disk 1, wo:0, o:1, dev:sdb1
Welcome to CenterPoint.
ix2 login:
INIT:
INIT: Running file /etc/init.d/rc
Stopping iSCSI-SCST target service: failed.
Removing iSCSI-SCST target modules: succeeded.
Running file /etc/rc0.d/K20rsync
Stopping rsync daemon: rsync.
Running file /etc/rc0.d/K20smartmontools
Stopping S.M.A.R.T. daemon: smartd.
Running file /etc/rc0.d/K23ntp
Stopping NTP server: ntpd.
Running file /etc/rc0.d/K25hwclock.sh
Saving the system clock.
Running file /etc/rc0.d/K25mdadm
Running file /etc/rc0.d/K63mountoverflowtmp
Running file /etc/rc0.d/K74bluetooth
Stopping bluetooth: hcid.
Running file /etc/rc0.d/K90rsyslog
Stopping enhanced syslogd: rsyslogd.
Running file /etc/rc0.d/S20sendsigs
Asking all remaining processes to terminate...mDNSResponder: mDNSResponder (Engineering Build) (Oct 4 2012 17:14:24) stopping
mDNSResponder: mDNS_FinalExit failed to send goodbye for: 0006CF28 01 29 _workstation._tcp.local. PTR ix2._workstation._tcp.local.
mDNSResponder: mDNS_FinalExit failed to send goodbye for: 0006E548 01 32 _LifeLineDevice._tcp.local. PTR ix2._LifeLineDevice._tcp.local.
done.
Killing all remaining processes... [31mfailed. [39;49m
Running file /etc/rc0.d/S30urandom
Running file /etc/rc0.d/S31umountnfs.sh
Running file /etc/rc0.d/S32portmap
Stopping portmap daemon....
Running file /etc/rc0.d/S35networking
Deconfiguring network interfaces...There is already a pid file /var/run/dhclient.eth0.pid with pid 1165
removed stale PID file
Internet Systems Consortium DHCP Client V3.1.1
Copyright 2004-2008 Internet Systems Consortium.
All rights reserved.
For info, please visit http://www.isc.org/sw/dhcp/
Listening on LPF/eth0/00:d0:b8:1d:78:bc
Sending on LPF/eth0/00:d0:b8:1d:78:bc
Sending on Socket/fallback
DHCPRELEASE on eth0 to 10.100.106.4 port 67
eth0: stopped
done.
Running file /etc/rc0.d/S36ifupdown
Running file /etc/init.d/ifupdown-clean
Cleaning up ifupdown....
Running file /etc/rc0.d/S50lvm2
Shutting down LVM Volume Groups Can't deactivate volume group "69f8850e_vg" with 1 open logical volume(s)
Can't deactivate volume group "md0_vg" with 2 open logical volume(s)
[31mfailed! [39;49m
Running file /etc/rc0.d/S60mdadm-raid
md: md1 still in use.
md: md0 still in use.
md: md1 still in use.
md: md0 still in use.
Stopping MD array md1... [31mfailed (busy). [39;49m
Stopping MD array md0... [31mfailed (busy). [39;49m
Running file /etc/rc0.d/S90halt
Will now halt.
INIT: cannot execute "/sbin/addLog"
INIT: no more processes left in this runlevel
0 logical volume(s) in volume group "69f8850e_vg" now active
md: md0 still in use.
md: md1 stopped.
md: unbind<sda2>
md: export_rdev(sda2)
Pivot root to /shutdown in RAM
0 logical volume(s) in volume group "md0_vg" now active
md: md0 stopped.
md: unbind<sdb1>
md: export_rdev(sdb1)
md: unbind<sda1>
md: export_rdev(sda1)
md: md1 stopped.
Drives are sd[ab]
/dev/sda:
/dev/sdb:
/dev/sda:
setting drive write-caching to 0 (off)
write-caching = 0 (off)
/dev/sdb:
setting drive write-caching to 0 (off)
write-caching = 0 (off)
/dev/sda:
issuing standby command
/dev/sdb:
issuing standby command
Mount table prior to shutdown:
rootfs on / type rootfs (rw)
none on /sysroot type tmpfs (rw,relatime,size=51200k,nr_inodes=30878)
tmpfs on / type tmpfs (rw,relatime)
proc on /proc type proc (rw,relatime)
sysfs on /sys type sysfs (rw,relatime)
Execute shutdown command: poweromd: stopping all md devices.
ff -f
sd 1:0:0:0: [sdb] Synchronizing SCSI cache
sd 0:0:0:0: [sda] Synchronizing SCSI cache
Power down.
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__| ** ix2-spi ** ** uboot_ver:0.0.8 **
** MARVELL BOARD: DB-88F6282A-BP LE
U-Boot 1.1.4 (Oct 28 2011 - 15:18:22) Marvell version: 3.6.1 - EMC
U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CD5A0
Soc: 88F6282 A1 CPU running @ 1600Mhz L2 running @ 800Mhz
SysClock = 533Mhz , TClock = 200Mhz
DRAM (DDR3) CAS Latency = 7 tRP = 7 tRAS = 20 tRCD=7
DRAM CS[0] base 0x00000000 size 256MB
DRAM Total size 256MB 16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
Found ADT7473, program PWM1 ... OK
[1024kB@f8000000] Flash: 1 MB
Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (6)
Device 0 @ 0 0:
Model: ST250DM000-1BD141 Firm: KC45 Ser#: 9VYHEAE0
Type: Hard Disk
Supports 48-bit addressing
Capacity: 238475.1 MB = 232.8 GB (488397168 x 512)
CPU : Marvell Feroceon (Rev 1)
Streaming disabled
Write allocate disabled
USB 0: host mode
PEX 0: interface detected no Link.
PEX 1: interface detected no Link.
Net: egiga0 [PRIME]
Hit any key to stop autoboot: 3 2 1 0
Reset IDE:
Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (6)
Device 0 @ 0 0:
Model: ST250DM000-1BD141 Firm: KC45 Ser#: 9VYHEAE0
Type: Hard Disk
Supports 48-bit addressing
Capacity: 238475.1 MB = 232.8 GB (488397168 x 512)
IDE read: device 0 block # 2048, count 6144 ... 6144 blocks read: OK
IDE read: device 0 block # 8192, count 6144 ... 6144 blocks read: OK
## Booting image at 00040000 ...
Image Name: Linux-2.6.31.8
Created: 2012-10-04 20:59:31 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2804428 Bytes = 2.7 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
## Loading Ramdisk Image at 00900000 ...
Image Name:
Created: 2012-11-09 21:52:49 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 2904981 Bytes = 2.8 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Starting kernel ...
Linux version 2.6.31.8 (soho@bsoho080.lss.emc.com) (gcc version 4.3.2 (Sourcery G++ Lite 2008q3-72) ) Thu Oct 4 16:59:24 EDT 2012 v0.0.9 Thu Oct 4 16:59:24 EDT 2012
CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977
CPU: VIVT data cache, VIVT instruction cache
Machine: Feroceon-KW
Using UBoot passing parameters structure
Memory policy: ECC disabled, Data cache writeback
Built 1 zonelists in Zone order, mobility grouping off. Total pages: 64960
Kernel command line: console=ttyS0,115200 root=/dev/ram0 mtdparts=spi_flash:0x7e000@0(u-boot),0x1000@0x7f000(env),0x1000@0x7e000(env2) :::DB88FXX81:eth0:none
PID hash table entries: 1024 (order: 10, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 256MB = 256MB total
Memory: 243968KB available (5196K code, 325K data, 140K init, 0K highmem)
Hierarchical RCU implementation.
NR_IRQS:128
Console: colour dummy device 80x30
Calibrating delay loop... 1589.24 BogoMIPS (lpj=7946240)
Security Framework initialized
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
xor: measuring software checksum speed
arm4regs : 1446.000 MB/sec
8regs : 1096.000 MB/sec
32regs : 1070.800 MB/sec
xor: using function: arm4regs (1446.000 MB/sec)
NET: Registered protocol family 16
Feroceon L2: Enabling L2
Feroceon L2: Cache support initialised.
CPU Interface
-------------
SDRAM_CS0 ....base 00000000, size 256MB
SDRAM_CS1 ....disable
SDRAM_CS2 ....disable
SDRAM_CS3 ....disable
PEX0_MEM ....base e0000000, size 128MB
PEX0_IO ....base f2000000, size 1MB
PEX1_MEM ....base e8000000, size 128MB
PEX1_IO ....base f2100000, size 1MB
INTER_REGS ....base f1000000, size 1MB
NFLASH_CS ....base fa000000, size 2MB
SPI_CS ....base f4000000, size 16MB
BOOT_ROM_CS ....no such
DEV_BOOTCS ....no such
CRYPT_ENG ....base f0000000, size 2MB
Marvell Development Board (LSP Version KW_LSP_5.1.3_patch25)-- DB-88F6282A-BP Soc: 88F6282 A1 LE
Detected Tclk 200000000 and SysClk 533333333
MV Buttons Device Load
Marvell USB EHCI Host controller #0: c8040740
PEX0 interface detected no Link.
PEX1 interface detected no Link.
PCI: bus0: Fast back to back transfers enabled
PCI: bus1: Fast back to back transfers enabled
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
raid6: int32x1 133 MB/s
raid6: int32x2 156 MB/s
raid6: int32x4 164 MB/s
raid6: int32x8 126 MB/s
raid6: using algorithm int32x4 (164 MB/s)
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
NET: Registered protocol family 1
Trying to unpack rootfs image as initramfs...
rootfs image is not initramfs (no cpio magic); looks like an initrd
Freeing initrd memory: 2836K
rtc mv_rtc: rtc core: registered kw-rtc as rtc0
RTC registered
XOR registered 4 channels
XOR 2nd invalidate WA enabled
cesadev_init(c000edd4)
mvCesaInit: sessions=640, queue=64, pSram=f0000000
MV Buttons Driver Load
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
squashfs: version 4.0 (2009/01/31) Phillip Lougher
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
SGI XFS with ACLs, security attributes, large block/inode numbers, no debug enabled
SGI XFS Quota Management subsystem
msgmni has been set to 482
alg: No test for cipher_null (cipher_null-generic)
alg: No test for ecb(cipher_null) (ecb-cipher_null)
alg: No test for digest_null (digest_null-generic)
alg: No test for compress_null (compress_null-generic)
alg: No test for stdrng (krng)
alg: No test for hmac(digest_null) (hmac(digest_null-generic))
async_tx: api initialized (sync-only)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
io scheduler noop registered
io scheduler anticipatory registered (default)
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xf1012100 (irq = 34) is a 16550A
console [ttyS0] enabled
brd: module loaded
loop: module loaded
Integrated Sata device found
IRQ 21/mvSata: IRQF_DISABLED is not guaranteed on shared IRQs
scsi0 : Marvell SCSI to SATA adapter
scsi1 : Marvell SCSI to SATA adapter
scsi 0:0:0:0: Direct-Access Seagate ST250DM000-1BD14 KC45 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] Sector size 0 reported, assuming 512.
sd 0:0:0:0: [sda] 488397168 512-byte logical blocks: (250 GB/232 GiB)
sd 0:0:0:0: [sda] 0-byte physical blocks
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 0:0:0:0: [sda] Write Protect is off
Loading Marvell Ethernet Driver:
o Cached descriptors in DRAM
o DRAM SW cache-coherency
o 2 Giga ports supported
o Single RX Queue support - ETH_DEF_RXQ=0
o Single TX Queue support - ETH_DEF_TXQ=0
o TCP segmentation offload (TSO) supported
o Large Receive offload (LRO) supported
o Receive checksum offload supported
o Transmit checksum offload supported
o Network Fast Processing (Routing) supported - (Disabled)
o Proc tool API enabled
o SKB Reuse supported - (Disabled)
o SKB Recycle supported - (Disabled)
o Rx descripors: q0=256
o Tx descripors: q0=532
o Loading network interface(s):
o register under mv88fx_eth platform
o eth0, ifindex = 2, GbE port = 0
Warning: Giga 1 is Powered Off
mvFpRuleDb (c0928000): 2048 entries, 8192 bytes
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA
sd 0:0:0:0: [sda] Sector size 0 reported, assuming 512.
SPI Serial flash detected @ 0xf4000000, 1024KB (256sec x 4KB)
3 cmdlinepart partitions found on MTD device spi_flash
Creating 3 MTD partitions on "spi_flash":
0x000000000000-0x00000007e000 : "u-boot"
0x00000007f000-0x000000080000 : "env"
0x00000007e000-0x00000007f000 : "env2"
sda:Using Hamming 1-bit ECC for NAND device
No NAND device found!!!
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci_marvell ehci_marvell.70059: Marvell Orion EHCI
ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus number 1
ehci_marvell ehci_marvell.70059: irq 19, io base 0xf1050100
sda1
sd 0:0:0:0: [sda] Sector size 0 reported, assuming 512.
sd 0:0:0:0: [sda] Attached SCSI disk
ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
uhci_hcd: USB Universal Host Controller Interface driver
usbcore: registered new interface driver usblp
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver ums-datafab
usbcore: registered new interface driver ums-freecom
usbcore: registered new interface driver ums-jumpshot
usbcore: registered new interface driver ums-sddr09
usbcore: registered new interface driver ums-sddr55
usbcore: registered new interface driver ums-usbat
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
adt7473 0-002e: adt7473 chip found
iBoard_model 2
md: linear personality registered for level -1
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
md: raid10 personality registered for level 10
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
dm_crypt using the OCF package.
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
TCP cubic registered
NET: Registered protocol family 17
NET: Registered protocol family 5
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
rtc mv_rtc: setting system clock to 2013-03-06 03:04:59 UTC (1362539099)
md: Waiting for all devices to be available before autodetect
md: If you don't use raid, use raid=noautodetect
md: Autodetecting RAID arrays.
md: Scanned 1 and added 1 devices.
md: autorun ...
md: considering sda1 ...
md: adding sda1 ...
md: created md0
md: bind<sda1>
md: running: <sda1>
raid1: raid set md0 active with 1 out of 2 mirrors
md0: detected capacity change from 0 to 21474770944
md: ... autorun DONE.
RAMDISK: gzip image found at block 0
VFS: Mounted root (ext2 filesystem) on device 1:0.
Looking for shell in cmdline: console=ttyS0,115200 root=/dev/ram0 mtdparts=spi_flash:0x7e000@0(u-boot),0x1000@0x7f000(env),0x1000@0x7e000(env2) :::DB88FXX81:eth0:none
Make node for mtd devices
HDD /dev/sda detected
cat: can't open '/sys/block/sdb/removable': No such file or directory
sh: mtd5: unknown operand
Create fw_env.config in /etc
Model name is ix2-ng
UUID_1 = 8018a9b4:8ff61352:c88cda7d:8f205803, size = 41943041
mdadm: No devices to examine
cat: can't open '/sys/block///size': No such file or directory
Valid Disk 1 in md0: /dev/sda1
Valid Disk 2 in md0:
USB Device node is /dev/sdb1
Checking to see the if the reset button is pressed or not
Started
/dev/btns file does not exist creating it
Opened /dev/btns with fd 3
Checking status of reset button
Button Check 1:
The Button ID from drive is 2 push_cntr is 0 release_cntr is 0
Button Check 2:
The Button ID from drive is 2 push_cntr is 0 release_cntr is 0
Button Check 3:
The Button ID from drive is 2 push_cntr is 0 release_cntr is 0
Button Check 4:
The Button ID from drive is 2 push_cntr is 0 release_cntr is 0
Button Check 5:
The Button ID from drive is 2 push_cntr is 0 release_cntr is 0
Button Check 6:
The Button ID from drive is 2 push_cntr is 0 release_cntr is 0
Button Check 7:
The Button ID from drive is 2 push_cntr is 0 release_cntr is 0
Button Check 8:
The Button ID from drive is 2 push_cntr is 0 release_cntr is 0
Button Check 9:
The Button ID from drive is 2 push_cntr is 0 release_cntr is 0
Button Check 10:
The Button ID from drive is 2 push_cntr is 0 release_cntr is 0
Reset Button is NOT pressed
Checking for valid image on system
md0: unknown partition table
md: md0 stopped.
md: unbind<sda1>
md: export_rdev(sda1)
mdadm: stopped /dev/md0
md: md0 stopped.
md: bind<sda1>
raid1: raid set md0 active with 1 out of 2 mirrors
md0: detected capacity change from 0 to 21474770944
mdadm: /dev/md0 has been started with 1 drive (out of 2).
md0: unknown partition table
1 logical volume(s) in volume group "md0_vg" now active
Found Valid EMC Image in disk...
Mounting apps image...
Mounting config image...
Check config filesystem
e2fsck 1.41.3 (12-Oct-2008)
ext2fs_check_if_mount: No such file or directory while determining whether /dev/loop1 is mounted.
No need to create fw_env.config
Create fw_env.config in /etc
Clean up the memory...
Constructing root filesystem...
Bootstrapping ...
rootdir=/
table='/usr/local/cfg/device_table.txt'
makedevs: line 42: chown failed for /bin/busybox: Read-only file system
makedevs: line 49: regular file '/usr/share/udhcpc/default.script' does not exist: No such file or directory
Loading ext3...
FATAL: Module ext3 not found.
Loading isofs...
Loading ntfs...
FATAL: Module ntfs not found.
Loading udf...
Loading ufsd...
ufsd: module license 'Commercial product' taints kernel.
Disabling lock debugging due to kernel taint
ufsd: driver 8.5 (Nov 2 2012 09:59:10) LBD=ON with delayalloc with ioctl loaded at bf029000
NTFS support included
Hfs+/HfsX support included
Built for: EMC_ix2_2Initialization complete.
Freeing init memory: 140K
INIT: version 2.86 booting
Running file /etc/init.d/rcS
Running file /etc/init.d/rc
Running file /etc/rcS.d/S01glibc.sh
Running file /etc/rcS.d/S02hostname.sh
Running file /etc/rcS.d/S02mountkernfs.sh
Running file /etc/rcS.d/S04mountdevsubfs.sh
Running file /etc/rcS.d/S05bootlogd
Running file /etc/rcS.d/S07hdparm
Setting parameters of disc: (none).
Running file /etc/rcS.d/S08hwclockfirst.sh
Setting the system clock.
Running file /etc/rcS.d/S11hwclock.sh
Setting the system clock.
Running file /etc/rcS.d/S12mtab.sh
mount: according to mtab, tmpfs is already mounted on /lib/init/rw
Running file /etc/rcS.d/S18ifupdown-clean
Cleaning up ifupdown....
Running file /etc/rcS.d/S20module-init-tools
Loading kernel modules...done.
Running file /etc/rcS.d/S26lvm2
Setting up LVM Volume Groups Reading all physical volumes. This may take a while...
Found volume group "md0_vg" using metadata type lvm2
1 logical volume(s) in volume group "md0_vg" now active
.
Running file /etc/rcS.d/S30checkfs.sh
Checking file systems...fsck 1.41.3 (12-Oct-2008)
done.
Running file /etc/rcS.d/S30procps
Setting kernel variables (/etc/sysctl.conf)...Running file /etc/rcS.d/S35mountall.sh
Mounting local filesystems...done.
Activating swapfile swap...done.
Running file /etc/rcS.d/S36mountall-bootclean.sh
Running file /etc/rcS.d/S37mountoverflowtmp
dhclient host identical
Running file /etc/rcS.d/S39ifupdown
Setting up networking....
Running file /etc/rcS.d/S40networking
Configuring network interfaces...done.
Running file /etc/rcS.d/S43portmap
Starting portmap daemon....
Running file /etc/rcS.d/S45mountnfs.sh
Running file /etc/rcS.d/S46mountnfs-bootclean.sh
Running file /etc/rcS.d/S55bootmisc.sh
Running file /etc/rcS.d/S55urandom
Running file /etc/rcS.d/S99stop-bootlogd-single
INIT: cannot execute "
INIT: Entering runlevel: 2
Running file /etc/init.d/rc
Running file /etc/rc2.d/S10rsyslog
Starting enhanced syslogd: rsyslogd.
Running file /etc/rc2.d/S12dbus
chown: invalid user: `messagebus'
Running file /etc/rc2.d/S20rsync
Running file /etc/rc2.d/S20smartmontools
Not starting S.M.A.R.T. daemon smartd, disabled via /etc/default/smartmontools [33m(warning). [39;49m
Running file /etc/rc2.d/S20sysfsutils
Setting sysfs variables....
Running file /etc/rc2.d/S23ntp
Starting NTP server: ntpdRunning file /etc/rc2.d/S25bluetooth
Starting bluetooth: hcidBluetooth: Core ver 2.15
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.13
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM ver 1.11
.
Starting netplugd...
eth0: link down
eth0: started
eth0: link up, full duplex, speed 1 Gbps
Generating RSA Key...
Generating public/private rsa1 key pair.
Your identification has been saved in /etc/ssh/ssh_host_key.
Your public key has been saved in /etc/ssh/ssh_host_key.pub.
The key fingerprint is:
57:51:74:95:9f:8a:9f:25:73:ab:5f:8d:51:4f:e8:9d
The key's randomart image is:
+--[RSA1 2048]----+
| .oo =|
| . + |
| . . =|
| . . =+|
| S . . +Eo|
| . . + =.|
| . B +|
| o ..|
| .o. |
+-----------------+
Starting sshd: OK
hostnamed begin to start...
Name now registered and active
hostnamed finished
IP obtaining in progress...
IP obtained
Starting executord
Done.
Running file /etc/rc2.d/S99rc.local
Running file /etc/rc2.d/S99rmnologin
Running file /etc/rc2.d/S99stop-bootlogd
Running file /etc/init.d/bootlogd
Welcome to CenterPoint.
ix2 login: md: bind<sda2>
md1: detected capacity change from 0 to 228550901760
md1: unknown partition table
XFS mounting filesystem dm-1
Welcome to CenterPoint.
ix2 login:
Welcome to CenterPoint.
ix2 login:
Welcome to CenterPoint.
ix2 login:
Welcome to CenterPoint.
ix2 login:
Welcome to CenterPoint.
ix2 login: admiAdding 524280k swap on /mnt/system/swapfile. Priority:-1 extents:4 across:8418776k
n
Password: XFS mounting filesystem dm-2
Login incorrect
ix2 login: root
Password:
root@ix2:/# uname -a
Linux ix2 2.6.31.8 Thu Oct 4 16:59:24 EDT 2012 v0.0.9 Thu Oct 4 16:59:24 EDT 2012 armv5tel GNU/Linux
root@ix2:/#
Broadcast message from root@ix2 (Tue Mar 5 19:08:56 2013):
The system is going down for system halt NOW!
INIT:
INIT: Running file /etc/init.d/rc
Stopping iSCSI-SCST target service: failed.
Removing iSCSI-SCST target modules: succeeded.
Running file /etc/rc0.d/K20rsync
Stopping rsync daemon: rsync.
Running file /etc/rc0.d/K20smartmontools
Stopping S.M.A.R.T. daemon: smartd.
Running file /etc/rc0.d/K23ntp
Stopping NTP server: ntpd.
Running file /etc/rc0.d/K25hwclock.sh
Saving the system clock.
Running file /etc/rc0.d/K25mdadm
Running file /etc/rc0.d/K63mountoverflowtmp
Running file /etc/rc0.d/K74bluetooth
Stopping bluetooth: hcid.
Running file /etc/rc0.d/K90rsyslog
Stopping enhanced syslogd: rsyslogd.
Running file /etc/rc0.d/S20sendsigs
Asking all remaining processes to terminate...mDNSResponder: mDNSResponder (Engineering Build) (Oct 4 2012 17:14:24) stopping
mDNSResponder: mDNS_FinalExit failed to send goodbye for: 0006CBD8 01 29 _workstation._tcp.local. PTR ix2._workstation._tcp.local.
mDNSResponder: mDNS_FinalExit failed to send goodbye for: 0006E1F8 01 32 _LifeLineDevice._tcp.local. PTR ix2._LifeLineDevice._tcp.local.
done.
Killing all remaining processes... [31mfailed. [39;49m
Running file /etc/rc0.d/S30urandom
Running file /etc/rc0.d/S31umountnfs.sh
Running file /etc/rc0.d/S32portmap
Stopping portmap daemon....
Running file /etc/rc0.d/S35networking
Deconfiguring network interfaces...There is already a pid file /var/run/dhclient.eth0.pid with pid 1147
removed stale PID file
Internet Systems Consortium DHCP Client V3.1.1
Copyright 2004-2008 Internet Systems Consortium.
All rights reserved.
For info, please visit http://www.isc.org/sw/dhcp/
Listening on LPF/eth0/00:d0:b8:1d:78:bc
Sending on LPF/eth0/00:d0:b8:1d:78:bc
Sending on Socket/fallback
DHCPRELEASE on eth0 to 10.100.106.4 port 67
eth0: stopped
done.
Running file /etc/rc0.d/S36ifupdown
Running file /etc/init.d/ifupdown-clean
Cleaning up ifupdown....
Running file /etc/rc0.d/S50lvm2
Shutting down LVM Volume Groups Can't deactivate volume group "192eefdb_vg" with 1 open logical volume(s)
Can't deactivate volume group "md0_vg" with 2 open logical volume(s)
[31mfailed! [39;49m
Running file /etc/rc0.d/S60mdadm-raid
md: md1 still in use.
md: md0 still in use.
md: md1 still in use.
md: md0 still in use.
Stopping MD array md1... [31mfailed (busy). [39;49m
Stopping MD array md0... [31mfailed (busy). [39;49m
Running file /etc/rc0.d/S90halt
Will now halt.
INIT: cannot execute "/sbin/addLog"
INIT: no more processes left in this runlevel
0 logical volume(s) in volume group "192eefdb_vg" now active
md: md0 still in use.
md: md1 stopped.
md: unbind<sda2>
md: export_rdev(sda2)
Pivot root to /shutdown in RAM
0 logical volume(s) in volume group "md0_vg" now active
md: md0 stopped.
md: unbind<sda1>
md: export_rdev(sda1)
md: md1 stopped.
Drives are sd[a]
/dev/sda:
/dev/sda:
setting drive write-caching to 0 (off)
write-caching = 0 (off)
/dev/sda:
issuing standby command
Mount table prior to shutdown:
rootfs on / type rootfs (rw)
none on /sysroot type tmpfs (rw,relatime,size=51200k,nr_inodes=30878)
tmpfs on / type tmpfs (rw,relatime)
proc on /proc type proc (rw,relatime)
sysfs on /sys type sysfs (rw,relatime)
Execute shutdown command: poweromd: stopping all md devices.
ff -f
sd 0:0:0:0: [sda] Synchronizing SCSI cache
Power down.
1 0
Reset IDE:
Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (6)
Device 0 @ 0 0:
Model: Hitachi HUA723030ALA640 Firm: MKAOA5C0 Ser#: MK0331YHGY11KA
Type: Hard Disk
Supports 48-bit addressing
Capacity: 764436.4 MB = 746.5 GB (1565565872 x 512)
[0 1 0]: Enable DMA mode (6)
Device 1 @ 0 1:
Model: Hitachi HUA723030ALA640 Firm: MKAOA5C0 Ser#: MK0331YHH2N46A
Type: Hard Disk
Supports 48-bit addressing
Capacity: 764436.4 MB = 746.5 GB (1565565872 x 512)
IDE read: device 0 block # 2048, count 6144 ... 6144 blocks read: OK
IDE read: device 0 block # 8192, count 6144 ... 6144 blocks read: OK
## Booting image at 00040000 ...
Image Name: Linux-2.6.31.8
Created: 2012-10-04 20:59:31 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2804428 Bytes = 2.7 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
## Loading Ramdisk Image at 00900000 ...
Image Name:
Created: 2012-11-09 21:52:49 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 2904981 Bytes = 2.8 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Starting kernel ...
Linux version 2.6.31.8 (soho@bsoho080.lss.emc.com) (gcc version 4.3.2 (Sourcery G++ Lite 2008q3-72) ) Thu Oct 4 16:59:24 EDT 2012 v0.0.9 Thu Oct 4 16:59:24 EDT 2012
CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977
CPU: VIVT data cache, VIVT instruction cache
Machine: Feroceon-KW
Using UBoot passing parameters structure
Memory policy: ECC disabled, Data cache writeback
Built 1 zonelists in Zone order, mobility grouping off. Total pages: 64960
Kernel command line: console=ttyS0,115200 root=/dev/ram0 mtdparts=spi_flash:0x7e000@0(u-boot),0x1000@0x7f000(env),0x1000@0x7e000(env2) :::DB88FXX81:eth0:none
PID hash table entries: 1024 (order: 10, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 256MB = 256MB total
Memory: 243968KB available (5196K code, 325K data, 140K init, 0K highmem)
Hierarchical RCU implementation.
NR_IRQS:128
Console: colour dummy device 80x30
Calibrating delay loop... 1589.24 BogoMIPS (lpj=7946240)
Security Framework initialized
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
xor: measuring software checksum speed
arm4regs : 1446.000 MB/sec
8regs : 1096.000 MB/sec
32regs : 1071.200 MB/sec
xor: using function: arm4regs (1446.000 MB/sec)
NET: Registered protocol family 16
Feroceon L2: Enabling L2
Feroceon L2: Cache support initialised.
CPU Interface
-------------
SDRAM_CS0 ....base 00000000, size 256MB
SDRAM_CS1 ....disable
SDRAM_CS2 ....disable
SDRAM_CS3 ....disable
PEX0_MEM ....base e0000000, size 128MB
PEX0_IO ....base f2000000, size 1MB
PEX1_MEM ....base e8000000, size 128MB
PEX1_IO ....base f2100000, size 1MB
INTER_REGS ....base f1000000, size 1MB
NFLASH_CS ....base fa000000, size 2MB
SPI_CS ....base f4000000, size 16MB
BOOT_ROM_CS ....no such
DEV_BOOTCS ....no such
CRYPT_ENG ....base f0000000, size 2MB
Marvell Development Board (LSP Version KW_LSP_5.1.3_patch25)-- DB-88F6282A-BP Soc: 88F6282 A1 LE
Detected Tclk 200000000 and SysClk 533333333
MV Buttons Device Load
Marvell USB EHCI Host controller #0: c8040740
PEX0 interface detected no Link.
PEX1 interface detected no Link.
PCI: bus0: Fast back to back transfers enabled
PCI: bus1: Fast back to back transfers enabled
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
raid6: int32x1 133 MB/s
raid6: int32x2 156 MB/s
raid6: int32x4 164 MB/s
raid6: int32x8 126 MB/s
raid6: using algorithm int32x4 (164 MB/s)
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
NET: Registered protocol family 1
Trying to unpack rootfs image as initramfs...
rootfs image is not initramfs (no cpio magic); looks like an initrd
Freeing initrd memory: 2836K
rtc mv_rtc: rtc core: registered kw-rtc as rtc0
RTC registered
XOR registered 4 channels
XOR 2nd invalidate WA enabled
cesadev_init(c000edd4)
mvCesaInit: sessions=640, queue=64, pSram=f0000000
MV Buttons Driver Load
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
squashfs: version 4.0 (2009/01/31) Phillip Lougher
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
SGI XFS with ACLs, security attributes, large block/inode numbers, no debug enabled
SGI XFS Quota Management subsystem
msgmni has been set to 482
alg: No test for cipher_null (cipher_null-generic)
alg: No test for ecb(cipher_null) (ecb-cipher_null)
alg: No test for digest_null (digest_null-generic)
alg: No test for compress_null (compress_null-generic)
alg: No test for stdrng (krng)
alg: No test for hmac(digest_null) (hmac(digest_null-generic))
async_tx: api initialized (sync-only)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
io scheduler noop registered
io scheduler anticipatory registered (default)
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xf1012100 (irq = 34) is a 16550A
console [ttyS0] enabled
brd: module loaded
loop: module loaded
Integrated Sata device found
IRQ 21/mvSata: IRQF_DISABLED is not guaranteed on shared IRQs
scsi0 : Marvell SCSI to SATA adapter
scsi1 : Marvell SCSI to SATA adapter
scsi 0:0:0:0: Direct-Access Hitachi HUA723030ALA640 MKAO PQ: 0 ANSI: 5
scsi 1:0:0:0: Direct-Access Hitachi HUA723030ALA640 MKAO PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] Sector size 0 reported, assuming 512.
sd 0:0:0:0: [sda] 5860533168 512-byte logical blocks: (3.00 TB/2.72 TiB)
sd 0:0:0:0: [sda] 0-byte physical blocks
sd 1:0:0:0: [sdb] Sector size 0 reported, assuming 512.
sd 1:0:0:0: [sdb] 5860533168 512-byte logical blocks: (3.00 TB/2.72 TiB)
sd 1:0:0:0: [sdb] 0-byte physical blocks
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 1:0:0:0: Attached scsi generic sg1 type 0
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA
sd 0:0:0:0: [sda] Sector size 0 reported, assuming 512.
sd 1:0:0:0: [sdb] Write Protect is off
Loading Marvell Ethernet Driver:
o Cached descriptors in DRAM
o DRAM SW cache-coherency
o 2 Giga ports supported
o Single RX Queue support - ETH_DEF_RXQ=0
o Single TX Queue support - ETH_DEF_TXQ=0
o TCP segmentation offload (TSO) supported
o Large Receive offload (LRO) supported
o Receive checksum offload supported
o Transmit checksum offload supported
o Network Fast Processing (Routing) supported - (Disabled)
o Proc tool API enabled
o SKB Reuse supported - (Disabled)
o SKB Recycle supported - (Disabled)
o Rx descripors: q0=256
o Tx descripors: q0=532
o Loading network interface(s):
o register under mv88fx_eth platform
o eth0, ifindex = 2, GbE port = 0
Warning: Giga 1 is Powered Off
mvFpRuleDb (c0b4a000): 2048 entries, 8192 bytes
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
sda:
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, supports DPO and FUA
sd 1:0:0:0: [sdb] Sector size 0 reported, assuming 512.
SPI Serial flash detected @ 0xf4000000, 1024KB (256sec x 4KB)
3 cmdlinepart partitions found on MTD device spi_flash
Creating 3 MTD partitions on "spi_flash":
0x000000000000-0x00000007e000 : "u-boot"
0x00000007f000-0x000000080000 : "env"
0x00000007e000-0x00000007f000 : "env2"
sdb:Using Hamming 1-bit ECC for NAND device
No NAND device found!!!
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci_marvell ehci_marvell.70059: Marvell Orion EHCI
ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus number 1
sda1 sda2
sd 0:0:0:0: [sda] Sector size 0 reported, assuming 512.
sd 0:0:0:0: [sda] Attached SCSI disk
ehci_marvell ehci_marvell.70059: irq 19, io base 0xf1050100
sdb1
sd 1:0:0:0: [sdb] Sector size 0 reported, assuming 512.
ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
sd 1:0:0:0: [sdb] Attached SCSI disk
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
uhci_hcd: USB Universal Host Controller Interface driver
usbcore: registered new interface driver usblp
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver ums-datafab
usbcore: registered new interface driver ums-freecom
usbcore: registered new interface driver ums-jumpshot
usbcore: registered new interface driver ums-sddr09
usbcore: registered new interface driver ums-sddr55
usbcore: registered new interface driver ums-usbat
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
adt7473 0-002e: adt7473 chip found
iBoard_model 2
md: linear personality registered for level -1
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
md: raid10 personality registered for level 10
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
dm_crypt using the OCF package.
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
TCP cubic registered
NET: Registered protocol family 17
NET: Registered protocol family 5
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
rtc mv_rtc: setting system clock to 2013-03-06 03:15:47 UTC (1362539747)
md: Waiting for all devices to be available before autodetect
md: If you don't use raid, use raid=noautodetect
md: Autodetecting RAID arrays.
md: Scanned 1 and added 1 devices.
md: autorun ...
md: considering sda1 ...
md: adding sda1 ...
md: created md0
md: bind<sda1>
md: running: <sda1>
raid1: raid set md0 active with 1 out of 2 mirrors
md0: detected capacity change from 0 to 21474770944
md: ... autorun DONE.
RAMDISK: gzip image found at block 0
VFS: Mounted root (ext2 filesystem) on device 1:0.
Looking for shell in cmdline: console=ttyS0,115200 root=/dev/ram0 mtdparts=spi_flash:0x7e000@0(u-boot),0x1000@0x7f000(env),0x1000@0x7e000(env2) :::DB88FXX81:eth0:none
Make node for mtd devices
HDD /dev/sda detected
HDD /dev/sdb detected
sh: mtd5: unknown operand
Create fw_env.config in /etc
Model name is ix2-ng
UUID_1 = 97bfab09:a493d4ee:9f6f6ebd:21db0b1f, size = 41943041
Valid Disk 1 in md0: /dev/sda1
Valid Disk 2 in md0:
USB Device node is /dev/sdc1
Checking to see the if the reset button is pressed or not
Started
/dev/btns file does not exist creating it
Opened /dev/btns with fd 3
Checking status of reset button
Button Check 1:
The Button ID from drive is 2 push_cntr is 0 release_cntr is 0
Button Check 2:
The Button ID from drive is 2 push_cntr is 0 release_cntr is 0
Button Check 3:
The Button ID from drive is 2 push_cntr is 0 release_cntr is 0
Button Check 4:
The Button ID from drive is 2 push_cntr is 0 release_cntr is 0
Button Check 5:
The Button ID from drive is 2 push_cntr is 0 release_cntr is 0
Button Check 6:
The Button ID from drive is 2 push_cntr is 0 release_cntr is 0
Button Check 7:
The Button ID from drive is 2 push_cntr is 0 release_cntr is 0
Button Check 8:
The Button ID from drive is 2 push_cntr is 0 release_cntr is 0
Button Check 9:
The Button ID from drive is 2 push_cntr is 0 release_cntr is 0
Button Check 10:
The Button ID from drive is 2 push_cntr is 0 release_cntr is 0
Reset Button is NOT pressed
Checking for valid image on system
md0: unknown partition table
md: md0 stopped.
md: unbind<sda1>
md: export_rdev(sda1)
mdadm: stopped /dev/md0
md: md0 stopped.
md: bind<sda1>
raid1: raid set md0 active with 1 out of 2 mirrors
md0: detected capacity change from 0 to 21474770944
mdadm: /dev/md0 has been started with 1 drive (out of 2).
md0: unknown partition table
2 logical volume(s) in volume group "md0_vg" now active
Found Valid EMC Image in disk...
Mounting apps image...
Mounting config image...
Check config filesystem
e2fsck 1.41.3 (12-Oct-2008)
ext2fs_check_if_mount: No such file or directory while determining whether /dev/loop1 is mounted.
No need to create fw_env.config
No need to create fw_env.config
Clean up the memory...
Constructing root filesystem...
Bootstrapping ...
rootdir=/
table='/usr/local/cfg/device_table.txt'
makedevs: line 42: chown failed for /bin/busybox: Read-only file system
makedevs: line 49: regular file '/usr/share/udhcpc/default.script' does not exist: No such file or directory
warning: can't open /etc/mtab: No such file or directory
Loading ext3...
FATAL: Module ext3 not found.
Loading isofs...
Loading ntfs...
FATAL: Module ntfs not found.
Loading udf...
Loading ufsd...
ufsd: module license 'Commercial product' taints kernel.
Disabling lock debugging due to kernel taint
ufsd: driver 8.5 (Nov 2 2012 09:59:10) LBD=ON with delayalloc with ioctl loaded at bf029000
NTFS support included
Hfs+/HfsX support included
Built for: EMC_ix2_2Initialization complete.
Freeing init memory: 140K
INIT: version 2.86 booting
Running file /etc/init.d/rcS
Running file /etc/init.d/rc
Running file /etc/rcS.d/S01glibc.sh
Running file /etc/rcS.d/S02hostname.sh
Running file /etc/rcS.d/S02mountkernfs.sh
Running file /etc/rcS.d/S04mountdevsubfs.sh
Running file /etc/rcS.d/S05bootlogd
Running file /etc/rcS.d/S07hdparm
Setting parameters of disc: (none).
Running file /etc/rcS.d/S08hwclockfirst.sh
Setting the system clock.
Running file /etc/rcS.d/S11hwclock.sh
Setting the system clock.
Running file /etc/rcS.d/S12mtab.sh
mount: according to mtab, tmpfs is already mounted on /lib/init/rw
Running file /etc/rcS.d/S18ifupdown-clean
Cleaning up ifupdown....
Running file /etc/rcS.d/S20module-init-tools
Loading kernel modules...done.
Running file /etc/rcS.d/S26lvm2
Setting up LVM Volume Groups Reading all physical volumes. This may take a while...
Found volume group "md0_vg" using metadata type lvm2
2 logical volume(s) in volume group "md0_vg" now active
.
Running file /etc/rcS.d/S30checkfs.sh
Checking file systems...fsck 1.41.3 (12-Oct-2008)
done.
Running file /etc/rcS.d/S30procps
Setting kernel variables (/etc/sysctl.conf)...Running file /etc/rcS.d/S35mountall.sh
Mounting local filesystems...done.
Activating swapfile swap...done.
Running file /etc/rcS.d/S36mountall-bootclean.sh
Running file /etc/rcS.d/S37mountoverflowtmp
Running file /etc/rcS.d/S39ifupdown
Setting up networking....
Running file /etc/rcS.d/S40networking
Configuring network interfaces...done.
Running file /etc/rcS.d/S43portmap
Starting portmap daemon....
Running file /etc/rcS.d/S45mountnfs.sh
Running file /etc/rcS.d/S46mountnfs-bootclean.sh
Running file /etc/rcS.d/S55bootmisc.sh
Running file /etc/rcS.d/S55urandom
Running file /etc/rcS.d/S99stop-bootlogd-single
INIT: cannot execute "
INIT: Entering runlevel: 2
Running file /etc/init.d/rc
Running file /etc/rc2.d/S10rsyslog
Starting enhanced syslogd: rsyslogd.
Running file /etc/rc2.d/S12dbus
chown: invalid user: `messagebus'
Running file /etc/rc2.d/S20rsync
Running file /etc/rc2.d/S20smartmontools
Not starting S.M.A.R.T. daemon smartd, disabled via /etc/default/smartmontools [33m(warning). [39;49m
Running file /etc/rc2.d/S20sysfsutils
Setting sysfs variables....
Running file /etc/rc2.d/S23ntp
Starting NTP server: ntpdRunning file /etc/rc2.d/S25bluetooth
Starting bluetooth: hcidBluetooth: Core ver 2.15
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.13
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM ver 1.11
.
Starting netplugd...
eth0: link down
eth0: started
eth0: link up, full duplex, speed 1 Gbps
ln: creating symbolic link `/etc/samba/smb.conf': File exists
Starting sshd: OK
hostnamed begin to start...
hostnamed finished
IP obtaining in progress...
IP obtained
Starting executord
Done.
Running file /etc/rc2.d/S99rc.local
Running file /etc/rc2.d/S99rmnologin
Running file /etc/rc2.d/S99stop-bootlogd
Running file /etc/init.d/bootlogd
Welcome to CenterPoint.
ix2 login: md: md1 stopped.
md: bind<sda2>
md1: detected capacity change from 0 to 2979084500992
md1: unknown partition table
XFS mounting filesystem dm-1
XFS mounting filesystem dm-2
Adding 524280k swap on /mnt/system/swapfile. Priority:-1 extents:4 across:4633812k
md: bind<sdb1>
RAID1 conf printout:
--- wd:1 rd:2
disk 0, wo:0, o:1, dev:sda1
disk 1, wo:1, o:1, dev:sdb1
md: recovery of RAID array md0
md: minimum _guaranteed_ speed: 1000 KB/sec/disk.
md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for recovery.
md: using 128k window, over a total of 20971456 blocks.
md: md0: recovery done.
RAID1 conf printout:
--- wd:2 rd:2
disk 0, wo:0, o:1, dev:sda1
disk 1, wo:0, o:1, dev:sdb1
Welcome to CenterPoint.
ix2 login:
INIT:
INIT: Running file /etc/init.d/rc
Stopping iSCSI-SCST target service: failed.
Removing iSCSI-SCST target modules: succeeded.
Running file /etc/rc0.d/K20rsync
Stopping rsync daemon: rsync.
Running file /etc/rc0.d/K20smartmontools
Stopping S.M.A.R.T. daemon: smartd.
Running file /etc/rc0.d/K23ntp
Stopping NTP server: ntpd.
Running file /etc/rc0.d/K25hwclock.sh
Saving the system clock.
Running file /etc/rc0.d/K25mdadm
Running file /etc/rc0.d/K63mountoverflowtmp
Running file /etc/rc0.d/K74bluetooth
Stopping bluetooth: hcid.
Running file /etc/rc0.d/K90rsyslog
Stopping enhanced syslogd: rsyslogd.
Running file /etc/rc0.d/S20sendsigs
Asking all remaining processes to terminate...mDNSResponder: mDNSResponder (Engineering Build) (Oct 4 2012 17:14:24) stopping
mDNSResponder: mDNS_FinalExit failed to send goodbye for: 0006CF28 01 29 _workstation._tcp.local. PTR ix2._workstation._tcp.local.
mDNSResponder: mDNS_FinalExit failed to send goodbye for: 0006E548 01 32 _LifeLineDevice._tcp.local. PTR ix2._LifeLineDevice._tcp.local.
done.
Killing all remaining processes... [31mfailed. [39;49m
Running file /etc/rc0.d/S30urandom
Running file /etc/rc0.d/S31umountnfs.sh
Running file /etc/rc0.d/S32portmap
Stopping portmap daemon....
Running file /etc/rc0.d/S35networking
Deconfiguring network interfaces...There is already a pid file /var/run/dhclient.eth0.pid with pid 1165
removed stale PID file
Internet Systems Consortium DHCP Client V3.1.1
Copyright 2004-2008 Internet Systems Consortium.
All rights reserved.
For info, please visit http://www.isc.org/sw/dhcp/
Listening on LPF/eth0/00:d0:b8:1d:78:bc
Sending on LPF/eth0/00:d0:b8:1d:78:bc
Sending on Socket/fallback
DHCPRELEASE on eth0 to 10.100.106.4 port 67
eth0: stopped
done.
Running file /etc/rc0.d/S36ifupdown
Running file /etc/init.d/ifupdown-clean
Cleaning up ifupdown....
Running file /etc/rc0.d/S50lvm2
Shutting down LVM Volume Groups Can't deactivate volume group "69f8850e_vg" with 1 open logical volume(s)
Can't deactivate volume group "md0_vg" with 2 open logical volume(s)
[31mfailed! [39;49m
Running file /etc/rc0.d/S60mdadm-raid
md: md1 still in use.
md: md0 still in use.
md: md1 still in use.
md: md0 still in use.
Stopping MD array md1... [31mfailed (busy). [39;49m
Stopping MD array md0... [31mfailed (busy). [39;49m
Running file /etc/rc0.d/S90halt
Will now halt.
INIT: cannot execute "/sbin/addLog"
INIT: no more processes left in this runlevel
0 logical volume(s) in volume group "69f8850e_vg" now active
md: md0 still in use.
md: md1 stopped.
md: unbind<sda2>
md: export_rdev(sda2)
Pivot root to /shutdown in RAM
0 logical volume(s) in volume group "md0_vg" now active
md: md0 stopped.
md: unbind<sdb1>
md: export_rdev(sdb1)
md: unbind<sda1>
md: export_rdev(sda1)
md: md1 stopped.
Drives are sd[ab]
/dev/sda:
/dev/sdb:
/dev/sda:
setting drive write-caching to 0 (off)
write-caching = 0 (off)
/dev/sdb:
setting drive write-caching to 0 (off)
write-caching = 0 (off)
/dev/sda:
issuing standby command
/dev/sdb:
issuing standby command
Mount table prior to shutdown:
rootfs on / type rootfs (rw)
none on /sysroot type tmpfs (rw,relatime,size=51200k,nr_inodes=30878)
tmpfs on / type tmpfs (rw,relatime)
proc on /proc type proc (rw,relatime)
sysfs on /sys type sysfs (rw,relatime)
Execute shutdown command: poweromd: stopping all md devices.
ff -f
sd 1:0:0:0: [sdb] Synchronizing SCSI cache
sd 0:0:0:0: [sda] Synchronizing SCSI cache
Power down.
Комментариев нет:
Отправить комментарий